Authinx Inc. MXV3RF Manual Do Utilizador

Check that the remote  is paired by 
waiting for the lights to go off on 
the remote and then press the FIND 
button on the RF2IR - the remote will 
play a "Hello Moto." Do this if you 
misplace your remote.

1. On the back of the remote, push 

down on tab and lift the cover off.

2. Match the batteries to the + and - 

marks inside the battery case, then 
insert 2 AA alkaline batteries.

3. Press the cover back into place.

If you install the RF2IR converter 
and "pair" it to the remote, you 
can use your remote anywhere up 
to 100 ft. from your STB without 
needing to point the remote at your 
STB. The RF2IR converter receives 
wireless (RF) commands from your 
remote and converts them to IR to 
control your STB. By default the 
remote transmits RF commands. 
You can set it to send IR commands 
if you don't want to use the RF2IR 
converter (see section L).

Plug the RF2IR converter into the 
USB port on the front of your Set 
Top Box.

MXv3RF

 remote

Your

original 

remote

1 inch 

apart

4. Enter the 4-digit code by pressing 

the numerical keys (0-9). The 
selected mode key light will blink 
for each digit entry and will remain 
off after the entry of the fourth 
digit - indicating a successful 
setup.

5. Point the remote control at the 

selected device and press the 
power key once. The device should 
turn off. If the device stayed on, 
repeat the steps 2 thru 5 trying each 
code for your brand until you fi nd 
the correct code.

Repeat the steps above  to setup 
another device. To use the remote 
control for your Set Top Box, press 
the STB mode key. 

NOTE: If an invalid code is entered or 
no key is pressed at all for 30 seconds, 
the mode key light flashes for 3 
seconds and turns off. The remote 
control returns to normal operation 
and you will need to start over from 
step B2 to setup the device.

To search for a particular device code 
for DVD or AUX e.g. VCR, use the 
Manual Programming for section B 
and program DVD or AUX with any 
VCR code prior to starting a search.

1. Turn on the device you want to 

control and point the remote at that 
device.

2. Press and hold the mode key (TV, 

DVD, or AUX) and while holding 
it pressed, press the OK key for 
one second. 

3. Release both keys, all the mode 

keys will fl ash then the selected 
mode key light will stay lit. 

4. Press the power button repetitively 

until the selected device turns off. 
Once your device has turned off, 
press OK to save the code. (If you 
overshoot the code, press chan 
down to go back, then press OK).

5. To indicate a successful setup, the 

selected mode key will turn off 
and you are ready to setup another 
device by following steps 1 thru 4 
of this section.

If the code for your device is not 
found in the code list and the search 
feature was not able to fi nd the code 
for your device, then the learning 
feature may be your best option. 
The learning feature lets you "learn" 
functions from your original remote 
control.

1. Press and hold a mode key (TV, 

DVD, or AUX) on the MXv3RF 
remote and while holding it 
pressed, press the LEARN key 
for one second then release both 
keys. 

2. All of the mode keys will fl ash and 

then the selected mode key light 
remains on.

3. On your MXv3RF remote, press 

and release the key that you want 
to teach.

4. While pointing your original 

remote at the bottom of your 
MXv3RF remote, approximately 
1 inch apart, press and hold the 
original remote key until the 
mode key light blinks once and 
stays on. (If there is a learning 
problem, the mode key light blinks 
for three seconds and stays on. If 
this happens, repeat steps 3 and 4 
above.)

4. Press and release the DELETE 

key. The mode key light turns off. 
All learned Commands under that 
mode are now cleared.

1. Press and hold the mode key (TV, 

DVD, or AUX) and while holding 
it pressed, press the LEARN key 
for one second then release both 
keys. 

2. All the mode keys will fl ash and 

the selected mode key light will 
stay on.

3. Press and release the LEARN key 

twice. The mode key light blinks 
off.

4. Press and release the DELETE 

key. The mode key light turns off. 

All learned Commands in the remote 
are now cleared.

The volume controls will control your 
Set Top Box until the TV device mode 
is programmed, e.g. if DVD mode is 
selected then volume controls your 
STB. If TV mode is programmed and 
DVD mode is selected, then volume 
controls your TV. 

If you'd like the volume commands 
to operate from just one device, 
e.g. always TV, then follow the 
instructions in Section F-I. If you'd 
like the volume commands to be 
sent to different devices depending 
which mode you are in, then follow 
the instructions in Section F-II.

1. Press the TV key and while 

holding it pressed, press the OK 
key for 1 second.

2. Release both keys, all of the mode 

keys will fl ash followed by the TV 
mode key light remaining on.

3. Press and hold the MUTE key for 

3 seconds until the TV mode key 
light briefl y turns off then remains 
on. Press and release the mode key 
that you always want to operate 
the volume commands (STB, TV, 
DVD, and AUX). The selected 
mode key light will remain on.

4. Press and release the MUTE key to 

save the setting. The selected mode 
key light will turn off indicating a 
successful setup. The volume 
commands will be setup for the 
selected device despite what mode 
is selected. If the selected mode 
key light fl ashes for 3 seconds and 
turns off, then the selected mode 
will have no volume commands 
of its own and will need to start 
over from step 1 above and select 
a different mode to program the 
device.

1. Press and hold the TV key and 

while holding it pressed, press the 
OK key for one second.

2. Release both keys, all of the mode 

keys will fl ash followed by the TV 
mode key light remaining on.

3. Press and hold the MUTE key for 

3 seconds until the TV mode key 
light briefl y turns off then stays on, 
then release the MUTE key. 

4. Press and release the MUTE key 

to save the setting. The TV mode 
key light turns off indicating 
successful setup. The volume 
commands will now work for 
different devices.

NOTE: If a programmed mode key 
has no volume commands of its 
own, then the volume control will 
normally operate the TV. If an invalid 
key is pressed, the selected mode key 
light fl ashes for 3 seconds and turns 
off. The remote control returns to 
normal operation and you will need 
to start over. 

If no key is pressed within 30 
seconds, the remote control times out, 
the selected mode key light fl ashes for 
3 seconds and turns off. The remote 
control returns to normal operation at 
which time you can start over.

The channel controls (Channel Up/
Down, 0-9 and LAST) will always 
work your Set Top Box. If you'd like 
the channel commands to be sent to 
different devices depending which 
mode you are in, then follow the 
instructions in Section G-I. 

1. Press and hold the TV key and 

while holding it pressed, press the 
OK key for one second.

2. Release both keys, all of the mode 

keys flash followed by the TV 
mode key light remaining on.

3. Press and hold the LAST key for 

3 seconds until the TV mode key 
light briefl y turns off then stays on, 
then release the LAST key. 

4. Press and release the LAST key 

to save the setting. The TV mode 
key light turns off indicating 
successful setup. The channel 
commands will now work for 
different devices. 

1. Press and hold the TV key and 

while holding it pressed, press the 
OK key for 1 second.

2. Release both keys, all of the mode 

keys will fl ash followed by the TV 
mode key light remaining on.

3. Press and hold the LAST key for 

3 seconds until the TV mode key 
light briefl y turns off then remains 
on. 

4. Press and release the STB mode 

key. The selected mode key light 
remains on.

5. Press and release the LAST key to 

save the setting.

The STB mode key light will turn off 
indicating a successful initial setup. 
The channel commands will be setup 
for your Set Top Box regardless of 
what mode is selected. If the selected 
mode key light fl ashes for 3 seconds 
and turns off, then you will need to 
start over from step 1.

To deactivate a device mode, then 
follow the instructions below: 

1. Press and hold the mode key to be 

deactivated (TV, DVD, or AUX) 
and while holding it pressed, press 
the OK key for one second.

2. Release both keys, all of the 

mode keys will flash and then 
the selected mode key light will 
remain on.

3. Enter the 4-digit code 1754 by 

pressing the numerical keys (0-9). 
The selected mode key light will 
blink for each digit entry and will 
remain off after the entry of the 
fourth digit - indicating the mode 
is deactivated.

Note the STB mode cannot be 
deactivated.

After pressing the STB key, pressing 
the Power key turns the Set Top Box 
on or off, AND turns on or off the TV 
if it has been setup. If you want the 
Power key to turn on other devices at 
the same time you can enable these 
as follows: 

1. Press and hold the STB key and 

while holding it pressed, press the 
OK key for 1 second. Then release 
both keys. You are now in setup 
mode.

2. Press and release the mode key 

(TV, DVD or AUX) you want to 
enable. 

3. Press and release the 1 key. The 

selected mode is now enabled. If 
no mode key is pressed instep 2 
ALL modes (TV, DVD and AUX) 
will be enabled.

To remove a mode from the Power 
key: 

1. Press and hold the STB key and 

while holding it pressed, press the 
OK key for 1 second. Then release 
both keys. You are now in setup 
mode.

2. Press and release the mode key 

(TV, DVD or AUX) you want to 
disable.

3. Press and release the 0 key. The 

selected mode is now disabled. If 
no mode key is pressed in step 2, 
ALL modes (TV, DVD and AUX) 
will be disabled. 

Note you can turn individual devices 
on/off by pressing the desired Mode 
key followed by the Power key. It 
is important to point your MXv3RF 
remote directly towards the devices 
for this feature to operate correctly. 

Your MXv3RF Remote Control has 
the ability to toggle between turning 
the backlights on or off. If you wish 
to use this feature, follow these 
instructions.

1. Press and hold the TV key and 

while holding it pressed, press the 
OK key for one second and release 
both keys at the same time.

2. All the mode keys fl ash and the TV 

mode key light stays on.

3. P r e s s   t h e   G U I D E   k e y,   a l l 

backlights will no longer turn on.

To reverse this process so that the 
backlights turn on when the remote 
control is being used, simply follow 
the same steps of the above section 
one more time.

1. Press and hold the TV key and 

while holding it pressed, press the 
OK key for one second and release 
both keys at the same time.

2. All the mode keys will fl ash, the 

TV mode key light will stay on.

3. Press and hold the DELETE key 

for 3 seconds until the TV mode 
key blinks and stays off. The 
remote control is now reset to 
factory default settings. If you 
want to use the remote control for 
your TV and other devices, you 
will need to setup the TV, DVD 
and AUX mode keys.

4. If no key is pressed within 30 

seconds, the remote control times 
out. The selected mode key light 
fl ashes for 3 seconds and turns 
off. The remote control returns 
to normal operation and you will 
need to start over.

You can toggle the STB key between 
RF and IR transmission (all other 
modes transmit IR always). The 
default for the STB key is RF. To 
change this to IR:

1. Press and hold the STB key.
2. While pressing the STB key, 

press the OK key.

3. Release both keys. The STB key 

lights up and stays on.

4. Press the PLAY key once. 

The STB key blinks off once for IR 
then stays off. To change back to RF 
transmission repeat steps above but 
press PLAY TWICE in step 4. The 
STB key blinks twice then stays off.
 
M. To set a specifi c "Pairing ID"

1. Press and hold the STB key.
2. While pressing the STB  key,
  press the OK key.
3. Release both keys. 
  The STB indicator stays on.
4. Press MENU key once.
5. Enter the 4 digits (0000 to 9999). 

The mode key light blinks for 
each digit and then remains off.

6. Pair the remote with the RF2IR as 

in section A.

1. Before plugging in the RF2IR 

receiver, press and hold the FIND 
key.

2. 

Plug the RF2IR converter into the 
USB port on the your STB 

while 

holding the FIND key.

3. Release the FIND key. All paired 

remotes are cleared.

You can only learn one device 
type under any one mode key. For 
example, only learn TV codes under 
the TV mode, DVD codes under the 
DVD mode, etc. If you are trying to 
learn from a "Universal" remote, it 
might have more than one code type 
stored under a mode. 

a. No functions may be stored under 

the LEARN key, or in the STB 
mode.

b. Depending on the remote you are 

trying to learn, some keys may not 
be learnable.

c. Only one original device type can 

be learned per individual mode.

d. Use fresh batteries for your 

o r i g i n a l   r e m o t e ,   a n d   y o u r 
MXv3RF Remote Control.

e.  Keep at least three feet away from 

incandescent or low-energy lights 
when learning.

f. Before learning, clear all learned 

commands (refer to Section E-II) 
then try learning 2 or 3 commands 
initially.

g. Point your original remote at the 

bottom end of your MXv3RF 
remote so the IR elements on 
both remotes are directly in line 
with each other (see diagram in 
section D). Adjust the height of 
either remote to achieve this.

h. Avoid learning your original 

remote's Volume/Mute keys unless 
you are sure these operate the 
same device.

i.  Avoid learning your original 

remote's VCR or DVD transport 
keys unless you’re sure these 
operate the same device.

j. If learning the fi rst or second keys 

for a mode results in continuous 
errors then try the following:

i.  End the learn session by pressing 

the LEARN key.

ii. Clear  out  the  learned  commands 

for that mode.

iii.Check the IR elements are 

correctly aligned between the 
two remotes.

iv. Adjust the distance between the 

two remotes to be closer (e.g. half 
an inch) or further away (e.g. 2 
inches) from each other.

v. Try learning the original remote 

for that mode again. If problems 
reoccur with the same key check 
the original remote key being 
learned – does it transmit? Does 
it operate the target device? Try 
learning that key under a different 
clear mode. If it learns OK then 
it is likely to be a different code 
type from the others and cannot 
be learned under the same mode.

5. Repeat steps 3 and 4 above for 

each key you want your MXv3RF 
Remote Control to learn. 

6. Press and release the LEARN key 

when all desired remote commands 
have been learned. If you have 
encountered diffi culties with the 
LEARN key setup, please refer 
to Section O: Troubleshooting 
Learning.

NOTE: It is not necessary to have 
your MXv3RF Remote Control 
learn every key from your original 
remote since most of the keys will 
not be used under normal daily use. 
The best practice is to teach only the 
keys that help you navigate for the 
best experience, like your volume up 
and down, channel up and down, and 
DVR functions.

1. Press and hold the mode key (TV, 

DVD, or AUX) and while holding 
it pressed, press the LEARN key 
for one second then release both 
keys. 

2. All the mode keys will fl ash and 

the selected mode key light will 
stay on.

3. Press and release the LEARN key 

once. The mode key light blinks 
off.

Before you can use the remote 
you need to "pair" it to the RF2IR 
converter, to do this:

1. Bring the remote close to the 

RF2IR converter. The remote will 
"pair" with the RF2IR when it is 
within about 2 feet from it. 

(You can pair up to 8 remotes with 
the RF2IR converter). You can now 
use your remote anywhere up to 100 
feet from your STB without needing 
to point the remote at your STB. 

The remote control will only control 
the device which is selected by the 
appropriate mode key (STB, TV, 
DVD, and AUX). The mode key light 
for the selected device fl ashes each 
time a valid key is pressed. In order 
to control other devices with your 
MXv3RF Remote Control, you need 
to tell the remote control what types 
of devices you have. Sections B and 
C take you through the steps needed 
to do this. The volume controls will 
control your Set Top Box (STB) until 
the TV device mode is setup. The 
channel controls will always control 
your STB. If you want to change 
this, you should follow the steps in 
Sections F & G.

To use your MXv3RF Remote 
Control for your other devices, you 
will need to setup the TV, DVD 
and AUX mode keys to control the 
devices (Section B). 

Please refer to the code list (on 
separate sheet) for a list of supported 
brands and models. If you do not 
fi nd the brand of your device on the 
supported code list, please refer to 
section C for the search function or 
you may use section C for instructions 
on the learning feature of your remote 
control. 

If you have an integrated or combo 
unit such as a TV/DVD, each 
component of the unit may need to 
be setup separately by setting up both 
the TV and DVD mode keys.

NOTE: The DVD and AUX mode 
keys can be setup with any code. 
The TV mode key can only be setup 
with TV codes.

Use the following steps to setup the 
TV, DVD or AUX mode keys:

1. Power on the device you want to 

program and locate the 4-digit 
code from the code list.

2. Press and hold the mode key (TV, 

DVD, or AUX) and while holding 
it pressed, press the OK key for 
one second. 

3. Release both keys, all of the mode 

keys will fl ash then the selected 
mode key light will stay lit. 

Note: Changes or Modifications 

not expressly approved by the  

Party responsible could void the 

user's authority to operate this 

device.