Authinx Inc. GB10A Manual Do Utilizador
Installing the GB10A Sensor
• Peel off the paper from the double sided tape on the back
and attach the Sensor to the inside of a window.
• Slide the battery compartment off and install two AA
alkaline batteries, observing polarity.
• Set the switch to 1 to make the unit more sensitive to the
sound of breaking glass, or 2 for less sensitive (helps
prevent false alarms).
prevent false alarms).
Glass Break/Light Sensor, Model GB10A Set Up and Operating Instructions
X-10 (USA) Inc., 91 Ruckman Rd., Closter, NJ 07624. www.x10.com
GB10A-8/99DR
Press and hold the TEST button for 10 seconds. The LED flashes
and then stays on. Press again, the LED blinks the current
Housecode setting (1 for A, 2 for B, etc.). Press the LED the
number of times for the new Housecode setting. The LED then
blinks back the setting.
and then stays on. Press again, the LED blinks the current
Housecode setting (1 for A, 2 for B, etc.). Press the LED the
number of times for the new Housecode setting. The LED then
blinks back the setting.
Replacing batteries
Open the battery compartment and replace the batteries with
two AA alkaline batteries. After replacing the batteries, the
following steps are necessary to determine that the Console still
recognizes the GB10A.
two AA alkaline batteries. After replacing the batteries, the
following steps are necessary to determine that the Console still
recognizes the GB10A.
• Place the Console’s slide switch to RUN2.
• Press TEST on the GB10A. If the Console chimes, it
• Press TEST on the GB10A. If the Console chimes, it
recognizes the GB10A and no further action is necessary.
If the Console did not chime:
Place the Console’s slide switch to INSTALL. Press TEST on
the GB10A. The Console beeps and logs in the GB10A to the
next available zone. To make sure the Console logs the GB10A
back into the same zone it was allocated to before you changed
the batteries, wait 4 hours after removing the old batteries before
reinstalling (until the zone indicator on the Console starts
flashing).
the GB10A. The Console beeps and logs in the GB10A to the
next available zone. To make sure the Console logs the GB10A
back into the same zone it was allocated to before you changed
the batteries, wait 4 hours after removing the old batteries before
reinstalling (until the zone indicator on the Console starts
flashing).
X-10 (USA) INC. LIMITED 1-YEAR WARRANTY
X-10 (USA) Inc. warrants X-10 products to be free from defective
material and workmanship for a period of one (1) year from the
original date of purchase at retail. X-10 (USA) Inc. agrees to
repair or replace, at it’s sole discretion, a defective X-10 product
if returned to X-10 (USA) Inc. within the warranty period and
with proof of purchase.
material and workmanship for a period of one (1) year from the
original date of purchase at retail. X-10 (USA) Inc. agrees to
repair or replace, at it’s sole discretion, a defective X-10 product
if returned to X-10 (USA) Inc. within the warranty period and
with proof of purchase.
If service is required under this warranty:
1. Return the defective unit postage prepaid to X-10 (USA)
Inc. at the address below.
2. Enclose a check for $4.00 to cover postage and handling.
3. Enclose a dated proof of purchase.
4. X-10 is not responsible for shipping damage.
3. Enclose a dated proof of purchase.
4. X-10 is not responsible for shipping damage.
F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF
THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE
MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO
THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID
THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE
MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO
THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID
THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
Registering the GB10A Sensor with the Security
Console
Console
• Set the slide switch on the Security Console to INSTALL.
• Press the TEST button on the GB10A Sensor. The console
• Press the TEST button on the GB10A Sensor. The console
beeps once to confirm and the next available zone LED
lights.
lights.
• Return the console slide switch to the RUN1 or RUN2
position.
Testing the GB10A Sensor
• Set the slide switch on the Security Console to RUN2.
• Press TEST on the GB10A. The console beeps to acknowl-
• Press TEST on the GB10A. The console beeps to acknowl-
edge and the zone LED lights.
*Note: you can install a total of 16 zones in the Console. This
can be a combination of Door/Window Sensors, Motion
Detectors, and Glass Break/Light Sensors. See your Security
System Owner’s Manual for more information.
can be a combination of Door/Window Sensors, Motion
Detectors, and Glass Break/Light Sensors. See your Security
System Owner’s Manual for more information.
Operation
When the security system is armed, the sound of breaking glass
within 20 feet of the GB10A will set off the alarm.
within 20 feet of the GB10A will set off the alarm.
Setting the Housecode for the GB10A Sensor
The GB10A also turns on a light (connected to an X10 Module)
when it gets dark and turns it off when it gets light. It always turns
on Modules set to Unit Code 1, but you can change the Housecode
that it transmits:
when it gets dark and turns it off when it gets light. It always turns
on Modules set to Unit Code 1, but you can change the Housecode
that it transmits:
Light
Sensor
Sensor
Glass
Break
Sensor
Break
Sensor
Glass
Break
Sensitivity
1 = High,
2 = Low.
Break
Sensitivity
1 = High,
2 = Low.