Authinx Inc. KR32A Manual Do Utilizador
Initializing Keyfob Remotes
Press and hold the ARM button on the Keyfob remote for 3-4 seconds
and then release it. This initializes the remote and picks a random
code that is used when it is registered with the Console.
and then release it. This initializes the remote and picks a random
code that is used when it is registered with the Console.
The default PIN is 0000, you can change this later, but for now press 0000 on the
keypad (under the lid to the bottom left of the display). This clears the top line and
shows * for each number entered.
keypad (under the lid to the bottom left of the display). This clears the top line and
shows * for each number entered.
This takes you to the first level of the menu at step 1. This is the INSTALLATION
level.
level.
Now simply press any button on the Keyfob remote. The Console acknowledges that
it has been registered by beeping and displaying RMOT 1 SET.
it has been registered by beeping and displaying RMOT 1 SET.
Repeat this for any other Keyfob Remotes you want to register. The display
increments to RMOT 2 SET, etc. as you install more remotes.
increments to RMOT 2 SET, etc. as you install more remotes.
Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO.
Pressing 1 takes you back to the HOME CONTROL screen. Pressing 2 takes you up
one level of menu.
Pressing 1 takes you back to the HOME CONTROL screen. Pressing 2 takes you up
one level of menu.
Registering the Keyfob Remote with the Console
Press either of the Menu up/down buttons (under the lid to the bottom left of the
display). The display then shows ENTER PIN (Personal Identification Number) in
the top line.
display). The display then shows ENTER PIN (Personal Identification Number) in
the top line.
Arming the system
Pressing ARM HOME on the Console arms all Door/Window Sensors instantly.
Motion Detectors will not trip the system when it is armed in the ARM HOME mode.
Pressing ARM AWAY arms with an exit delay and an entry delay, to give you time to
disarm the system after you enter your home. These delays will be what you specified
for your ENTRY DELAY (30 second default) and EXIT DELAY (1 minute default).
Motion Detectors will not trip the system when it is armed in the ARM HOME mode.
Pressing ARM AWAY arms with an exit delay and an entry delay, to give you time to
disarm the system after you enter your home. These delays will be what you specified
for your ENTRY DELAY (30 second default) and EXIT DELAY (1 minute default).
Pressing ARM on the Keyfob remote always arms in the AWAY mode. This arms all
Door/Window Sensors AND Motion Detectors, but arms instantly.
Door/Window Sensors AND Motion Detectors, but arms instantly.
Disarming the system
Pressing DISARM on the Keyfob remote disarms the system instantly.
To disarm from the Console: Enter your 4 digit PIN (Personal Identification
Number) this will be 0000 unless you changed it.
Number) this will be 0000 unless you changed it.
Entering the PIN clears the top line and shows * for each number entered.
When you see INSTALL on the display. Press OK and the display looks like this:
ENTER PIN
12:00 am
12:00 am
****
12:00 am
12:00 am
1. INSTALL
1. INSTALL
ZONE
ZONE
ARMED HOME
12:00 am
12:00 am
****
12:00 am
12:00 am
DISARMED
12:00 am
12:00 am
Panic Alarm:
Pressing BOTH Panic buttons at the same time trips the alarm, even
if the system was not armed.
If the unit is armed it will disarm when the PIN is entered, and return to the time
display, with DISARMED in the top line.
Then after a short delay the display reverts to HOME CONTROL mode.
Then after a short delay the display reverts to HOME CONTROL mode.