GN Netcom ACTIVA24 Manual Do Utilizador

Put on the headset.

Set the headset/handset selector
to headset position.

Lift the handset
from the phone.
Answer or place
the call.

You can now move
freely up to 10
meters away from the
base (depending on
the environment of
your office). If you
move out of trans-
mission range, you
will hear a signal in
the headset every 10
seconds.

To end the call,
replace the handset
on the phone.

Netcom

Max 10 m

To increase or decrease the
volume, press the upper (+)
or lower (-) part of the oval
volume control on the head-
set. When the volume reach-
es maximum or minimum,
you will hear a signal in
your headset.

To talk without the other
party hearing you, press
the mute button on the
headset. When the micro-
phone is muted, you will
hear a signal every 3 sec-
onds. When the mute
function is on, you can
still hear the other party.

To ensure optimum
battery life, when not
in use, place the headset
in the base with the
headset/handset selector
in the handset position.
The battery charging
indicator illuminates
during recharging. It
takes 3 hours to fully
charge the battery.
When fully charged, the
indicator flashes. A
fully charged batter
provides 7 hours of
talktime. If battery
power gets too low, you
will hear a signal in
your headset every 20
seconds.

Upon request only, you must notify your telephone utility company (telco) of your intention to install or permanently remove an
FCC Part 68 registered device or system. Include the FCC Registration Number and the Ringer Equivalence Number (REN) located
on the amplifier label.

The telco has the right to make changes to their network, which may affect the operation of your equipment, provided you are given
adequate advance written notice to permit correct operation.

This device complies with part 15 of the FCC Rules and ICES-003 Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The Industry Canada label identifies certified equipment.  This certification means that the equipment meets telecommunications
network protective, operational and safety requirement as prescribed in the appropriate Terminal Equipment Technical Resource
Document(s).  The department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local 
telecommunications company.  The equipment must also be installed using an acceptable method of connection.  The customer
should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier.  Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the
user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and 
internal metallic water pipe system, if present, are connected together.  This precaution may be particularly important in rural
areas. Caution:  Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.

NOTICE:  The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum 
number of terminals allowed to be connected to a telephone interface.  The termination of an interface may consist of any 
combination of devices subject only to the requirement that the sum of the ringer equivalence Numbers of all the devices does 
not exceed 5.

54-???? Activa2.4  7/14/00  4:01 PM  Page 3