Mobilaris AB 466B Manual Do Utilizador
User Manual:
Mobilaris long-life personnel tag
Mobilaris long-life personnel tag
Mobilaris offers a set of various WiFi tags that enables
localization of personnel and mobile equipment (such
as vehicles or machinery) within the WiFi network.
These tags transmit a beacon signal (in CCX blink
mode, including the MAC address of the tag) in certain
intervals to the WiFi access points network. Using
special algorithms, the information is used to
determine the position of each tag.
localization of personnel and mobile equipment (such
as vehicles or machinery) within the WiFi network.
These tags transmit a beacon signal (in CCX blink
mode, including the MAC address of the tag) in certain
intervals to the WiFi access points network. Using
special algorithms, the information is used to
determine the position of each tag.
Inside of a network where the Mobilaris Mining
Intelligence (MMI) system is not enabled, the tag will
continue to function as a standard WiFi tag, sending
out CCX blink signals at a defined standard interval or
at a factory configured interval.
Intelligence (MMI) system is not enabled, the tag will
continue to function as a standard WiFi tag, sending
out CCX blink signals at a defined standard interval or
at a factory configured interval.
If a tag is used within a network that supports the
Mobilaris Mining Intelligence system, more
functionality is enabled:
Mobilaris Mining Intelligence system, more
functionality is enabled:
• Tags can be automatically updated over the air
(OTA) with software updates or new configuration
(such as blink rates, sleep times, IP address of the
receiving MMI etc).
(such as blink rates, sleep times, IP address of the
receiving MMI etc).
• The Tag can be configured to communicate with
MMI when the tag is near an exciter (in order to
increase accuracy or to open a gate or similar).
increase accuracy or to open a gate or similar).
• Personnel tags can be configured to communicate
with MMI when the user has pressed a dedicated
button on the tag.
button on the tag.
The long-life personnel tag is equipped with a
powerful battery with a life cycle of up to three years
(depending on transmission rates and other
configurable parameters).
The tag has the following additional functionalities:
• Two multi-functional push-buttons (P1 and P2).
• A LED light indicator that provides specific
• A LED light indicator that provides specific
indications but can also be customized for various
indications.
indications.
• An additional antenna that can sense an optional
exciter (magnetic bubble) and trigger extra
beacons and MTP Updates sent up to MMI.
beacons and MTP Updates sent up to MMI.
• A battery saving mechanism that can put the tag
into sleep mode by decreasing the blink rate and
by that increasing the battery time. This happens if
the tag has not been moving during a configurable
amount of time.
by that increasing the battery time. This happens if
the tag has not been moving during a configurable
amount of time.
Using the Mobilaris Mining Intelligence system, the
tag can be configurated and its firmware can be
updated over the air (OTA). This can also be explicitly
achieved by a short press of the P2 button in normal
state or automatically over a configurable period of
time (i.e. every few hours/days).
tag can be configurated and its firmware can be
updated over the air (OTA). This can also be explicitly
achieved by a short press of the P2 button in normal
state or automatically over a configurable period of
time (i.e. every few hours/days).
In the unusual use case where a person configures a
tag erroneously so that the tag cannot reach the MMI
or the OTA server, there are procedures to get it back
to life:
tag erroneously so that the tag cannot reach the MMI
or the OTA server, there are procedures to get it back
to life:
• If a tag cannot connect to the MMI system, a
preconfigured fall-back OTA server can be utilized
by a long-press on the P2 button.
by a long-press on the P2 button.
• If the P1 and P2 buttons are being pressed
together for 10 seconds, the tag is forced into a
hardware reset.
hardware reset.
Using the push-buttons or the battery saving
mechanism, the tag can switch between three
different states as described to the right:
mechanism, the tag can switch between three
different states as described to the right: