MARKLYN GROUP INC 77091 Manual Do Utilizador
RGB test
77091 {3 RGB<1、2、3>、3 white<4、5、6>}
一、test ways: Bluetooth is powering on.
1, Touch ALPENA RGB starter
2, Bluetooth search interface STASM-12E54B ">"
3, the car interface (check the color to ensure that the lighting color is the same)
4, click on the number 1, 2, 3, enter the Color Selection interface
1) Select the color; check the color to ensure that the lighting color is the same
2) Adjust the brightness of each color, check the light bar is the same
3) Check the Custom selection and check the light bar if changes with touching
4) Way 1: to save the color, click on "Save" and the color wheel, then click on the number
1, 2, 3, 4, 5, 6, check the selected color is saved in the corresponding number box
一、test ways: Bluetooth is powering on.
1, Touch ALPENA RGB starter
2, Bluetooth search interface STASM-12E54B ">"
3, the car interface (check the color to ensure that the lighting color is the same)
4, click on the number 1, 2, 3, enter the Color Selection interface
1) Select the color; check the color to ensure that the lighting color is the same
2) Adjust the brightness of each color, check the light bar is the same
3) Check the Custom selection and check the light bar if changes with touching
4) Way 1: to save the color, click on "Save" and the color wheel, then click on the number
1, 2, 3, 4, 5, 6, check the selected color is saved in the corresponding number box
Way 2: click the number box → Save → wheel color, and checking the number box and
the color of the light is the same.
5, click "Scenes" → "Scenes Selection" interface, and to test the every models, focusing on
"Try me" click, from the red>green > white, but Speed cannot be adjusted.
二 (test for white led “4; 5; 6”)
二 (test for white led “4; 5; 6”)
1 click AlPENA RGB Starter
2 Bluetooth search interface STASM-12E53A “>”
2 Bluetooth search interface STASM-12E53A “>”
3 In “car” interface observe the color and check whether the emitting color is consistent or
not
4 click the number “4; 5; 6” respectively, and then enter into on/off selection
5 adjust every mode to check whether it is consistent with corresponding led strip
6 see whether the brightness adjustment is right or not
5 adjust every mode to check whether it is consistent with corresponding led strip
6 see whether the brightness adjustment is right or not
三 test for color groups “1; 2; 3”
1 click the Grouping button and then enter into grouping interface; click number “1; 2/3” and
then finish the grouping; finally, enter into interface “color selection” and check whether the
color of these two grouping strips are consistent with that of adjustment
1 click the Grouping button and then enter into grouping interface; click number “1; 2/3” and
then finish the grouping; finally, enter into interface “color selection” and check whether the
color of these two grouping strips are consistent with that of adjustment
2 click the number “1; 2; 3” respectively, and then enter into on/off selection
1) Select the color and then observe the color to check whether the emitting color is
consistent or not
2) Adjust the brightness and observe whether the corresponding strips are right or not
3) Adjust custom selection and observe whether the corresponding strips are right or
3) Adjust custom selection and observe whether the corresponding strips are right or
not
4) Method 1: firstly, click the custom selection respectively and then save the operation;
secondly, click the number “1; 2; 3; 4; 5; 6”, observe whether the selected color is stored in
the corresponding number box
the corresponding number box
Method2: click the number box and then save the operation; observe the color the
number box is consistent with that of the strip
3, click Scenes → Scenes Selection interface, select each mode, observing whether the two
3, click Scenes → Scenes Selection interface, select each mode, observing whether the two