TAKENAKA ENGINEERING CO. LTD. COM-50XTL Manual Do Utilizador

— TABLE OF CONTENTS —

1-2

Refer to “1-3 NAMES OF
OPERATION SECTION”

Viewfinder

Horizontal angle fine
adjustment screw (White)

Vertical angle adjustment
screw (Red)

Vertical angle
adjustment screw (Red)

Wiring terminal

Function settings

Swivel base (White)
(Horizontal angle adjustment)

Cut bush

Mounting plate : 2pcs

Rear side of mounting plate

Grommet

Slide fixing screw

Plate fixing screw
Caution : Do not tighten or
loosen the screw

Adjustment plate

Rubber cap (both side)

Swing arm (Red)
(Vertical angle adjustment)

Microwave unit

Photoelectric beam unit

Cover fixing screw

ACCESSORIES

Sensor body : 2 pcs (transmitter : 1pc, receiver : 1 pc)

COM-50XT

Transmitter : Fluorescent yellow
Receiver : Fluorescent orange

Sensor fixing screw : 2 pcs

Cover x 2 pcs

Self-tapping screw for mounting

Ø4 x 30 : 8 pcs

Countersunk oval-head

screw (M4 x 20) : 8 pcs

Cable tie

: 4 pcs

Anti-bird spike

: 4 pcs

Instruction manual

: 1 pc

Swivel base (Black)
(Horizontal angle adjustment)

Check that the transmitter, receiver,
and accessories indicated below are included
in the box when you first unpack the product.

Waterproof film
Caution : Do not peel off or damage the waterproof film

○

1. PRODUCTS COMPONENTS
1-1 PARTS DESCRIPTION.................................................................. 2
1-2 ACCESSORIES.............................................................................. 2
1-3 NAMES OF OPERATION SECTION.............................................. 3

2. PRECAUTIONS.................................................................................... 3

3. BEFORE INSTALLATION
3-1 PROTECTION DISTANCE AND DETECTION RANGE................. 4
3-2 MOUNTING HEIGHT...................................................................... 5
3-3 ADJUSTMENT RANGE.................................................................. 5
3-4 EXAMPLE OF PRACTICAL APPLICATION.................................... 5

4. MOUNTING METHOD
4-1. WALL MOUNTING METHOD........................................................ 6
4-2. POLE MOUNTING METHOD......................................................... 7

5. WIRING METHOD
5-1. POSITION AND RATING OF TERMINALS................................... 8
5-2. WIRING DISTANCE BETWEEN SENSOR AND POWER SUPPLY........ 8
5-3. WIRING DISTRIBUTION DIAGRAM (WIRING DIAGRAM)........... 8

6. AREA ADJUSTMENT
6-1. METHOD OF AREA ADJUSTMENT.............................................. 9
6-2. NAMES AND FUNCTIONS OF MICROWAVE SENSOR.............. 9
6-3. NAMES AND FUNCTIONS OF PHOTOELECTRIC BEAM SENSOR......10
6-4. NAMES OF THE OPERATION SECTION.....................................10

6-5. ALIGNMENT OF MICROWAVE SENSOR...................................11
6-6. ALINGMENT OF PHOTOELECTRIC BEAM SENSOR................13

7. OPERATION CHECK...........................................................................14

8. EXPLANATION OF FUNCTIONS
8-1. MODULATION FREQUENCY SELECTION.................................15
8-2. BEAM TRANSMISSION POWER SELECTION............................15
8-3. BEAM TOWER SELECTION........................................................15
8-4. ALARM MEMORY DISPLAY.........................................................16
8-5. SOUND CHECK............................................................................16
8-6. ENVIRONMENT/ALARM OUTPUT SELECTION.........................16
8-7. AND/OR-GATE SETLECTION......................................................16
8-8. RESPONSE TIME ADJUSTMENT................................................17
8-9. MICROWAVE/PHOTOELECTRIC BEAM CHANGEOVER...........17
8-10. AUTO GAIN LOCK......................................................................18
8-11. PROGRAMMABLE AGC.............................................................18
8-12. LIGHT SENSITIVITY SIGNAL.....................................................18
8-13. EXTERNAL ENVIRONMENT DIAGNOSTIC...............................18
8-14. ALIGNMENT WIRELESS CHECKER CONNECTION................18

9. TROUBLESHOOTING..........................................................................19

10. SPECIFICATIONS................................................................................20

11. EXTERNAL DIMENSIONS...................................................................20

1-1

PRODUCT COMPONENTS

PARTS DESCRIPTION

• Check that the following transmitter, receiver, and accessories are included in the box when

you first unpack the product.

This section describes the contents of the product package and the names and
functions of the parts that appear in this instruction manual.

T : Transmitter R : Receiver label on rear surface

Pole mounting attachment

Ø1.65"(Ø42mm) to Ø1.95"(Ø49mm)