Guangzhou Vensi Intelligent Technology Co. Ltd. ZE321BX Manual Do Utilizador
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
the user's authority to operate the equipment.
(OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF Module. Additional
measurements (15C) and/or equipment authorizations (e.g either a complete new certification or a Class II
Permissive Change) may need to be addressed depending on co-location or simultaneous transmission issues if
applicable.
measurements (15C) and/or equipment authorizations (e.g either a complete new certification or a Class II
Permissive Change) may need to be addressed depending on co-location or simultaneous transmission issues if
applicable.
OEM/Integrator shall include instructions or statements in the host user’s manual that are required by Part 15.19
and 15.21
Guidance will be provided to the Integrator for compliance with the Part 15B requirement.
Integrator is reminded to assure that these installation instructions will not be made available to the end-user of the
final host device.
final host device.
the Integrator will be responsible to satisfy SAR/ RF Exposure requirements, when the module integrated into any
(mobile, fixed) host device.
(mobile, fixed) host device.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm
between the radiator & your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The final host device, into which this RF Module is integrated" has to be labelled with an auxilliary lable stating the
FCC ID of the RF Module, such as "Contains FCC ID:
FCC ID of the RF Module, such as "Contains FCC ID:
2AR6I-ZE321BX". (e.g either a complete new
certification
or a Class II Permissive Change) may need to be addressed depending on co-location or
simultaneous transmission issues if applicable.