ICOM 333800 Manual Do Utilizador
REMOTE-CONTROL MICROPHONE
HM-195B
HM-195SW
INSTRUCTIONS
e
¤2
Receiving DSC calls
Receiving a Distress Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
Push a softkey to select your desired action.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
ating channel to Channel 16. After that, monitor it, as a coast
station may require assistance.
station may require assistance.
Receiving a Distress Acknowledgement
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
Push a softkey to select your desired action.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
ating channel to Channel 16. After that, monitor it, as a coast
station may require assistance.
station may require assistance.
Receiving a Distress Relay Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
Push a softkey to select your desired action.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
ating channel to Channel 16. After that, monitor it, as a coast
station may require assistance.
station may require assistance.
Receiving a Distress Relay Acknowledgement
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
Push a softkey to select your desired action.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
Push to display the Received call information. (See ¤3)
[ACPT]
Push to accept the call, then push [CH 16] to switch the oper-
ating channel to Channel 16. After that, monitor it, as a coast
station may require assistance.
station may require assistance.
Receiving an Individual Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
• If [ALARM OFF] is not pushed within 2 minutes, the next screen
may appear, depending on the received Category.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACK]
Push to display the “INDIVIDUAL ACK” screen to reply to the
Push to display the Received call information. (See ¤3)
[ACK]
Push to display the “INDIVIDUAL ACK” screen to reply to the
Call, and select the channel specified by the calling station
for voice communication, depending on your situation. See
¤1
for voice communication, depending on your situation. See
¤1
for details of the Individual Acknowledgement procedure.
When “INDIVIDUAL ACK” is set to “Auto ACK (Unable),” the
transceiver automatically replies to the Call. In that case,
both the TX and RX calls are stored in the Transmitted and
Received Call Logs.
transceiver automatically replies to the Call. In that case,
both the TX and RX calls are stored in the Transmitted and
Received Call Logs.
Receiving a Group Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
• If [ALARM OFF] is not pushed within 2 minutes, the next screen
may appear, depending on the received Category.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACPT]
Push to monitor the channel specified by the calling station for
Push to display the Received call information. (See ¤3)
[ACPT]
Push to monitor the channel specified by the calling station for
it’s announcement.
Receiving an All Ships Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
• If [ALARM OFF] is not pushed within 2 minutes, the next screen
may appear, depending on the received Category.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACPT]
Push to monitor the channel specified by the calling station for
Push to display the Received call information. (See ¤3)
[ACPT]
Push to monitor the channel specified by the calling station for
it’s announcement.
Receiving a Geographical Area Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
• If [ALARM OFF] is not pushed within 2 minutes, the next screen
may appear, depending on the received Category.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACPT]
Push to monitor the channel specified by the calling station for
Push to display the Received call information. (See ¤3)
[ACPT]
Push to monitor the channel specified by the calling station for
it’s announcement.
When no GPS receiver is connected, or if there is a problem
with the connected receiver, all Geographical Area Calls are
received, regardless of your position.
with the connected receiver, all Geographical Area Calls are
received, regardless of your position.
Receiving a Position Request Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
• If [ALARM OFF] is not pushed within 2 minutes, the next screen
may appear, depending on the received Category.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACK]
Push to display the “POSITION REPLY” screen and send a
Push to display the Received call information. (See ¤3)
[ACK]
Push to display the “POSITION REPLY” screen and send a
reply to the Call. (See ¤1)
When “POSITION ACK” is set to “Auto TX,” the transceiv-
er automatically replies to the Call. In that case, both the
TX and RX calls are stored in the Transmitted and Re-
ceived Call Logs.
er automatically replies to the Call. In that case, both the
TX and RX calls are stored in the Transmitted and Re-
ceived Call Logs.
Receiving a Position Report Call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
• If [ALARM OFF] is not pushed within 2 minutes, the next screen
may appear, depending on the received Category.
Push a softkey to select your desired action.
w
[EXIT]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
Push to display the Received call information. (See ¤3)
Receiving a Polling Request call
D
Push [ALARM OFF] to stop the alarm and the blinking back-
q
light.
• If [ALARM OFF] is not pushed within 2 minutes, the next screen
may appear, depending on the received Category.
Push a softkey to select your desired action.
w
[IGN]
Push to ignore the Call and return to the normal operating
Push to ignore the Call and return to the normal operating
mode.
[INFO]
Push to display the Received call information. (See ¤3)
[ACK]
Push to display the “POLLING REPLY” screen to reply to the
Push to display the Received call information. (See ¤3)
[ACK]
Push to display the “POLLING REPLY” screen to reply to the
Call. (See ¤1)
When “POSITION ACK” is set to “Auto TX,” the transceiv-
er automatically replies to the Call. In that case, both the
TX and RX calls are stored in the Transmitted and Re-
ceived Call Logs.
er automatically replies to the Call. In that case, both the
TX and RX calls are stored in the Transmitted and Re-
ceived Call Logs.
¤2
Receiving DSC calls (Continued)