ICOM 384302 Manual Do Utilizador

- 2 -

- 3 -

D

Indicators
q

 

Displays the relative receive signal strength level.

w 

  Displays the current time.



  “AM” or “PM” is displayed beside the time display when 12 

hour display format is selected.

e 

    Displayed or blinks to indicate the battery status.

Indication

Battery 

status

Full

Mid

Charging

required

Battery

exhausted

 

 blinks when the battery is exhausted.

Icons
The following icons are displayed in the Icon Area.

 •“L1” is displayed when the output power is set to Low.

 •“L2” is displayed when the output power is set to Mid.

 •“H” is displayed when the output power is set to High.

Displayed when the channel is in the ‘audible’ (unmute) 

mode.

MESSAGE ICON  

 • Blinks after messages (Message or Status Message) have been 

received.

 • Stops blinking when the screen is changed, or any key is pushed, 

but is displayed if unread messages are still in the Message 

memory.

 • Disappears when all messages in the Message memory have 

been read.

 Displayed when a matching signal is received, depending 

on the presetting.

SCAN ICON  

 • Displayed when a scan is paused.

 •Blinks while scanning.

 Displayed when the channel is selected as a scan target channel.

NOTE: The screen capture is an example.

The displayed position of each icon may differ, depending 

on the function being used.

Icon Area

Text Area

Key Display

Area

q

w

e

 Displayed when the Voice Scrambler function is ON.

 •Displayed when valid position data is received.

 •Blinks when searching for satellites or calculating position data.

 •Displayed when the Record function is ON.

 •Blinks while recording audio.



  “     ” is displayed when there is no microSD card free space and 

audio cannot be recorded.

TALK AROUND ICON  
Displayed when the Talk Around function is ON.

 • Displayed when the transceiver is connected to a telephone 

network on the selected channel.

 •Blinks while receiving a phone call.

Displayed when the Lone Worker function is ON.

Displayed when the Motion Sensor function is ON.

Displayed when the Noise Cancel function is ON. 

Displayed when the Surveillance function is ON.

Displayed when the Vibration function is ON.

Displayed when the VOX function is ON.

 •Displayed when Bluetooth

® 

is activated.

 •Lights Blue when a Bluetooth

®

 device is connected.

 • Does not light when no Bluetooth

®

 device is connected.

Displayed when a microSD card is inserted into the card slot.



   “ ” is displayed when the microSD card has not been formatted.

Displayed when a USB device is connected.

D

Displays the selected Zone number, Channel number, and 

Channel name, if set.

D

Displays the names of the function assigned to [P1] and [P2].



  Ask your dealer about the assigned Software key functions.

D

NOTE: Before using the transceiver for the fi rst time, the 

battery pack must be fully charged for optimum life and 

operation. See the BATTERY CHARGING section of this 

sheet.

Rotate [VOL] to turn ON the transceiver.

D

1.   Select a channel.

 • Rotate [Selector] or push [Up] or [Down], depending 

on the presetting.

2.   When receiving a call, rotate [VOL] to adjust the audio 

output level to a comfortable listening level.

CAUTION: Attach an antenna before transmitting. 

Transmitting without an antenna may damage the 

transceiver.

1.  Wait until the channel is clear to avoid interference.

2.   While holding down [PTT], speak at your normal voice 

level. 

3.  Release [PTT] to receive.

To maximize the readability of your signal:

1.  After pushing [PTT], pause briefl y before you start 

speaking.

2.  Hold the microphone 5 to 10 cm (2 to 4 inches) from 

your mouth, then speak at your normal voice level.

D

D

You can rapidly charge up to 6 battery packs with the 

optional BC-214.

Approximately 2.8 hours for the BP-283

 • The  BC-157S 

AC

 

ADAPTER

 or the OPC-656 

DC

 

POWER

 

CABLE

 • The  AD-132 

CHARGER

 

ADAPTER

 (may be supplied with the 

charger, depending on the charger version)

CAUTION: NEVER reverse the polarity when connecting 

the OPC-656 to a power source. This will ruin the battery 

charger.

Red line: +, Black line: _

OPC-656
Connect to a 

DC power supply: 

12 to 16 V, at least 7 A

Red line:   +  

Black line: _

Turn 

To an AC outlet

You can rapidly charge the Li-ion battery pack with the 

BC-219 or BC-225.

BC-219: 2.8 hours for the BP-283

BC-225: 2.5 hours for the BP-283

 • A power adapter (may be supplied with the charger, 

depending on the charger version) or the OPC-515L/CP-23L 

DC

 

POWER

 

CABLES

.

 • A USB cable to connect the PC and BC-225 when using the RS-

BC225.

CAUTION: NEVER reverse the polarity when connecting 

the OPC-515L to a power source. This will ruin the battery 

charger.
White line: +, Black line: _

 • Before detaching or attaching a battery pack, 

BE SURE to turn OFF the transceiver by rotating [VOL] fully counter clockwise, until it makes a 

“click” sound. Otherwise, a transceiver malfunction could occur.

 • The internal clock will be reset to 00:00 if an exhausted battery is left in the transceiver, or the battery pack is detached, for long periods of time.

*   Charger  adapter’s shape may differ, 

depending on the charger version.

The 

 ( for a 13.8 V DC 

power source) or the 

CP-23L (for a 12 V 

cigarette lighter 

socket) can be 

used instead of the 

power adapter.

To a PC with 

the RS-BC225 

installed.*

1

Power Adapter*

2

Turn 

*

1  

The RS-BC225 is usable for only with the 

BC-225.

*

2  

A different type, or no power adapter is 

supplied, depending on the charger version.