Precision Planting LLC 725801 Manual Do Utilizador
955125 5 08/13
FCC/IC Information
FCC/IC Statements
FCC ID 2AAJN‐725801
This device complies with Part 15 of the FCC Rules. Opera on is subject to the following two condi ons: (1) this
device may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired opera on.
device may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired opera on.
Changes or modifica ons not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
authority to operate the equipment.
To comply with FCC/IC RF exposure limits for general popula on/uncontrolled exposure, the antenna(s) used for this
transmi er must be installed to provide a separa on distance of at least 20cm from all persons and must not be co‐
located or opera ng in conjunc on with any other antenna or transmi er.
transmi er must be installed to provide a separa on distance of at least 20cm from all persons and must not be co‐
located or opera ng in conjunc on with any other antenna or transmi er.
IC: 11204A‐725801
This device complies with Industry Canada License‐exempt RSS standard(s). Opera on is subject to the following two
condi ons: (1) this device may not cause interference and (2) this device must accept any interference, including
interference that may cause undesired opera on of the device.
condi ons: (1) this device may not cause interference and (2) this device must accept any interference, including
interference that may cause undesired opera on of the device.
Cet appareil est conforme avec les norme(s) exemp on de licences RSS d’Industrie Canada. Opéra on est sujet au
deux condi ons suivantes. (1) Cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toute
interference, y compris les interferences qui peuvent causer un mauvais fonc onnement de l’appareil.
deux condi ons suivantes. (1) Cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toute
interference, y compris les interferences qui peuvent causer un mauvais fonc onnement de l’appareil.
OEM Responsibili es to comply with FCC and Industry Canada Regula ons
The Wi‐Fi module has been cer fied for integra on into products only by OEM integrators under the following condi ons:
1.
The antenna(s) must be installed such that a minimum separa on distance of 20cm is maintained between the
radiator (antenna) and all persons at all mes.
radiator (antenna) and all persons at all mes.
2.
The transmi er module must not be co‐located or opera ng in conjunc on with any other antenna or transmi er. As
long as the two condi ons above are met, further transmi er tes ng will not be required. However, OEM integrators
is s ll responsible for tes ng their end‐product for any addi onal compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
long as the two condi ons above are met, further transmi er tes ng will not be required. However, OEM integrators
is s ll responsible for tes ng their end‐product for any addi onal compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
Important Note: In the event that these condi ons cannot be met (for certain configura ons or co‐loca on of another transmi er),
then the FCC and Industry Canada authoriza ons are no longer considered valid and the FCC ID and IC Cer fica on Number cannot
be used for the final product. In these circumstances, the OEM integrator will be responsible for re‐evalua ng the end product
(including the transmi er) and obtaining a separate FCC and Industry Canada authoriza on.
then the FCC and Industry Canada authoriza ons are no longer considered valid and the FCC ID and IC Cer fica on Number cannot
be used for the final product. In these circumstances, the OEM integrator will be responsible for re‐evalua ng the end product
(including the transmi er) and obtaining a separate FCC and Industry Canada authoriza on.
End Product Labeling
The Wi‐Fi module is labeled with its own FCC ID and IC Cer fica on Number. If the FCC ID and IC Cer fica on Number are not visible
when the module is installed inside another device, then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the
following:
when the module is installed inside another device, then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the
following:
“Contains Transmi er Module FCC ID: 2AAJN‐725801”
“Contains Transmi er Module IC: 11204A‐725801”
or
“Contains FCC ID: 2AAJN‐725801”
“Contains IC: 11204A‐725801”
The OEM of the Wi‐Fi module must only use the approved antenna(s) listed above, which have been cer fied with this module.
The OEM integrator has to be aware not to provide informa on to the end user regarding how to install or remove this RF module or
change RF related parameters in the user manual of the end product.
“Contains Transmi er Module IC: 11204A‐725801”
or
“Contains FCC ID: 2AAJN‐725801”
“Contains IC: 11204A‐725801”
The OEM of the Wi‐Fi module must only use the approved antenna(s) listed above, which have been cer fied with this module.
The OEM integrator has to be aware not to provide informa on to the end user regarding how to install or remove this RF module or
change RF related parameters in the user manual of the end product.