Paofit Technology Pte Ltd PFTK002 Manual Do Utilizador

Awesome! You've got the PaofitTrack. It's going to make your digital running experience 
even better. While it’s kind of obvious how the sensor works do read this quick guide so 
you get the best out of it. 

Before placing PaofitTrack in position, ensure treadmill track is not moving. 

WARNING: 

Place PaofitTrack on the floor directly underneath mid-section of the treadmill where the 
PaofitTrack Main Wheel      can clearly access the treadmill track underside.

 Ensure the Main Wheel     is only in contact with the tread and is not too 

close to the treadmill frame or the front or rear of the treadmill.

 Ensure the PaoftTrack is placed in the same direction as the treadmill track 

which means it's not at an angle.

1. USB port
2. Jack Input
3. Security Bar
4. Main Wheel
5. Small Wheel
6. Release Button
7. Charging Light
8. Bluetooth Light
9. Arm
10. Power Switch
11. Extension Leg Holes 

(b) RELEASING ARM AND ADJUSTING FOR HEIGHT
Once in position, press the Release Button     . This will cause the Main Wheel      to swing
upwards and make contact with the treadmill track.  The Arm      should not have swing to 
its maximum height for the Main Wheel      to make contact. Ideally the Arm      should swing 
up a little leaving a decent additional swing for when the treadmill tilt is used. 

I. Pull the Main Wheel      block to extend 
   the Arm until the Release Button clicks. 
   To restore Arm length, simply press the 
   Release Button      and shorten the Arm 
   length holding the Main Wheel     .

II. Insert the two Extension Legs into the 
    Extension Leg holes      in the base of the 
    PaofitTrack. 

• PaofitTrack can be turned on via the Power Switch      located on the underside.
• If PaofitTrack is plugged into an external power source PaofitTrack will go into hibernation 
  (sleep mode) once the Main Wheel      has not moved for at least 3 hours.
• If PaofitTrack is using the internal battery source PaofitTrack will go into hibernation (sleep 
  mode) once the Main Wheel      has not moved for at least 10 minutes.
• To reactivate (wake up) PaofitTrack from hibernation, the Main Wheel      should be rotated 
  for at least 3 seconds. 
• To fully switch off PaofitTrack, turn off the Power Switch      located on the underside.

use PaofitTrack only within following environment conditions:

WARNING: 

0°C-45°C and 90% humidity.

PaofitTrack connects to the Paofit App using Blue Tooth Low Energy (BTLE).  This is 
managed within the Paofit App. It is not managed via Apple's Settings area. 
Before trying to connect, first check PaofitTrack's Bluetooth Light      is flashing blue. 
• If the Bluetooth Light      is not glowing blue it means PaofitTrack is either in hibernation or 
  switched off completely (see Section 3). 
• If the Bluetooth Light      is glowing blue constantly it means PaofitTrack is already 
  connected to a Paofit App.  
• If the Bluetooth Light      is flashing blue it means it is ready to connect. In the Paofit App, 
  select a video, then pull up the User Control Panel and select the Bluetooth option at the 
  bottom of the User Control Panel. 
  This will pull up a list of PaofitTrack signals. Click on your PaofitTrack signal to connect. 

• The default Bluetooth signal name is “PT Sensor”.  To change this to a name of your 
  preference, log in to your Paofit account when connected online. Then go to PaofitTrack 
  settings within the Paofit App Settings area.
• The first time you change the name of your PaofitTrack’s Bluetooth signal, it will be paired 
  with your Paofit account, and this account will now have the sole authorization to change 
  that name in the future. The Bluetooth signal will also automatically connected to your 
  account every time it comes within range. 

• A security bar     is located at the front of the treadmill under the Main Wheel. This can be
  used to attach a security wire where there is concern the PaofitTrack may be at risk of theft. 
  It is presumed the wire would then be secured to the treadmill.
• Small Wheel      for Incline: Some PaofitTrack models may include a “Small Wheel”     . 
  Versions with the Small Wheel      also measure treadmill incline. If applicable, incline data 
  will automatically be visible on the App user interface.
• Jack Input:      PaofitTrack has a 3.5mm jack input located at the front. This is normally 
  not in use but may be required by some versions of the Paofit App that will access 
  PaoftTrack data via the jack. 

Size : 110 x 262mm

Size : 110 x 262mm

B

C

with input voltage of 110-240V, output power is 5V, 1A. By example, an iPad plug charger 
would be suitable.

ensure the micro-USB cable which is with a ferrite core does not get trapped under

WARNING: 

treadmill frame. This should include checking whether the cable is affected 

and fully lowering the treadmill's incline function. 

(b) INTERNAL BATTERY
• PaofitTrack comes with an internal battery so it can function without an external power 
  source. When PaofitTrack is connected to an external power source, the internal battery is 
  automatically recharged while recharging. 
• The Charging Light     on the Arm will glow red. Once the battery is fully charged the 
  Charging Light      will glow green.
• You can view how charged the battery is by clicking on the Bluetooth sensor option in the 
  App User Control Panel. The level of charge will be shown next to the Bluetooth signal 
  name.  

(a) EXTERNAL POWER SOURCE
To connect PaofitTrack to a power source, insert the micro-USB cable into the PaofitTrack
USB port       and plug the USB into a laptop, computer or similar. Charging from the a wall
socket may also be done by connecting the USB cable to a standard CE certified USB plug

or pinched by the 

 after fully lifting