JIANGSU HORIZON NEW ENERGY TECHNOLOGIES LTD FCJJ25 Manual Do Utilizador

WARNING

• Avoid running into obstacles. Collisions could cause damage to the car.

• Slowly and carefully press the refueling station’s plunger down to ﬁll the car’s fuel tank.

• The instruction sheet must be kept since it contains important information.

• This product is intended only for use by persons aged 8 years and older, and only under the supervision of an adult who has read and understands

the instructions provided in this user manual.

• Do not use the refueling station other than for refueling the i-H2GO car as instructed in this user manual.

• Do not turn on the refueling station without adding water as instructed in this user manual. Do not submerge the refueling station in water, only ﬁll

the refueling station with water as instructed in this manual.

• Keep the refuelling station and the i-H2GO car away from any ﬁre or ﬂame.

• Read this manual carefully before use.

• Do not attempt to use any part, item or components provided in this product for any purposes other than for its intended use.

• Do not attempt to disassemble any parts, item or component in this kit.

Trouble shooting - i-H2GO car

1. The car lost Bluetooth connection and it did not re-pair automatically.

Please turn the car “OFF”, wait about 3 seconds, turn the car “ON” and check to see if there are blue ﬂashing lights in the car. If there are no ﬂashing

blue lights, connect the car to the "Refueling Station", wait till the left LED turns green and turn "ON'" the car. If the car still does not pair, go to

Bluetooth, click the (>) next to the device, select "Forget this Device" and follow the pairing steps again．

2. Purging the car is very important.

Pressing the built-in purge valve will release any atmospheric gases inside the car fuel system if the fuel tank is empty. You can also use a small quantity

of hydrogen to perform another purge and this ensures the car’s fuel system is ﬁlled only with pure hydrogen fuel for optimal performance.

3. The car is moving slower than before, for a shorter time or stops without using all of its fuel.

Check to see if there is hydrogen in the fuel tank. Was the left LED in the refueling station green before you unplugged the car? If so, purge the car’s fuel

tank and perform the warm up procedures (2 or 3 times). Ensure the playing surface is ﬂat and clean. Check to see if there is hydrogen in the fuel tank.

You can also turn the car “OFF” wait 3 seconds and then turn it “ON”.

4. Having trouble steering?

Use tweezers to clear away any debris on the car’s front axles and wheels.

5. The balloon won’t ﬁll up.

Clear any blockages or debris from the refueling station output valve and the car’s input valve. Make sure the output valve is correctly and fully inserted.

Ensure the refueling station’s rubber plug is securely in place.

6. Water has not been removed from the refueling station properly and has gone into the car’s fuel tank during refueling.

Properly empty the water from the refueling station via the “Rubber Cap”. Purge and warm up the car. Switch “OFF” the car and store it for one day

before using again.

Trouble shooting - Refueling Station

1. Bubbles are coming out from the bottom opening, not the top opening.

Use a cotton swab to block the bottom opening until the bubbles comes out from the top again. Turn the refueling station“OFF”, wait for 3 minutes and

turn it back “ON”.

Taking care of your i-H2GO

Safe Storage

Switch both the car and refueling station “OFF” before storing. Empty the refueling station of all hydrogen and water and unplug the

refueling station from any power supply before storing. Lay both units ﬂat on a clean space and allow to dry. The units should be stored in

the original box in a cool, dry place.

Cleaning

Your i-H2GO is an advanced piece of engineering and you need to take good care of it to ensure you get many enjoyable hours of play out

of it. Always make sure the unit is switched “OFF” and unplugged from any power source before cleaning. Wipe the car and the refueling

station with a soft and clean moist cloth. Be sure to dry the car thoroughly by wiping away all excess water. When cleaning the refueling

station make sure to clean both the top and bottom of the unit before storing. It is a good idea to allow the refueling station to air dry for

30 minutes before storing. The car’s fuel cell also needs to be well ventilated while drying.

Filling the refueling station

WARNING: Placing any other liquid besides distilled/puriﬁed water inside the refueling station will result in permanent damage to the

unit. Even tap/ﬁltered water will damage the unit over time.

www.horizonfuelcell.com

2. No bubbles are coming out (try the following 4 steps).

a. Ensure there is enough water in the refueling station. It should cover the top outlet.

b. Check to see if the right LED light is green. If not, charge the refueling station.

c. Switch “OFF” the unit and unplug it from power supply. After 3 minutes turn the unit “ON”

d. Empty the refueling station and reﬁll with fresh distilled or puriﬁed water.

3. The refueling station won’t restart or has stopped halfway through.

Check to be sure the station is “ON”, ﬁlled properly with water and the “Rubber Cap” is secure. If so, turn “OFF” the refueling station, open the

refueling station’s “Rubber Cap” and press the plunger all the way down (be careful it is normal that some water will come out). Close the “Rubber

Cap” securely. Then turn the refueling station back “ON”. If there is still no hydrogen production, please charge the refueling station until the right

LED light is green.

4. Parts of the refueling station which are not meant for water are wet or the unit has fallen in water.

WARNING: Water and electricity cause electric shock. Immediately disconnect the refueling station from any power supply, switch it “OFF” and dry

the wet components with a soft cloth. Pay special attention to any water residing in recesses or gaps. Pour out any water from inside of the unit

through the slots on the bottom of the refueling station. Do not use the unit for at least one hour, or place unit in a warm spot to help the water

evaporate.

5. How do I empty water from the refueling station?

Hold the refueling station with both hands beside a sink or basin. Pour the water out of the water tank slowly from the front of the unit. Hold it

upside down until all of the water has run out of the water tank. Wipe and dry the unit before storing. Any water remaining in the tubes is safe and

does not need to be removed.

You must only use distilled/puriﬁed

water with the refueling station.

7. I cannot control the car.

The i-H2GO has a control range of up to 15 meters (about 50 feet). Be aware that electrical interference and obstacles might reduce this range.

8. I cannot start the car after the balloon is fully ﬁlled with hydrogen.

Are you sure the green LED light on the left side of the "Refueling Station" was green? If so, please purge the gas tank and warm the car up using Step 7.

6. The plunger does not move, but there are bubbles coming out.

This sometimes happens when using the refueling station for the ﬁrst time. Make sure the “Rubber Cap” is attached securely. The plunger might need

loosening. Lightly guide the plunger up until the station is full of hydrogen and there are no more bubbles. Do this lightly as excessive force might

damage the refueling station.

7. Hydrogen production is very slow.

Make sure the refueling station is ﬁlled with water. Switch “OFF” the refueling station, wait 10 minutes and turn it back “ON”. If production is still slow,

please charge the refueling station until the right LED light is green.

Importer:

Horizon Fuel Cell Europe spol. s r. o.

Vaclavske namesti 1

Praha 1, 110 00

Czech Republic

Manufacturer:

Jiangsu Horizon New Energy Technologies Ltd.

3th Floor, Block C, No.9 Guangdong Road, Zhangjiagang Free Trade Zone,

Jiangsu Province, China