Huizhou Qingteng Electro Technology Co. Ltd. WVD01BELL Manual Do Utilizador

2. Connect and screw the 8~24VAC wire terminals to the 2 points of 17

     TP1and TP2 on the back plate. If no AC wires to be connected, 

     please skip this step.

Install the 2 rechargeable batteries on the back of main unit.

Please see and go through the section E to set up and pair the device.

1. Insert the 3 supporting hooks on the main unit into the supporting 

    hole on the back plate and pull the main unit down to locate it on 

    the back plate.

2. Screw the screw hole with the included screw and hex wrench and 

     the main unit is tightly fastened to the back plane.

Open the App Store (for iOS) or the Google Play Store(for Android) 

on your mobile devices. 

Search for "Ubell" or scan the following QR Code to download and 

install to your device.

 The device has to be installed at the place where a WiFi is available. 

1. Allocate and mark 4 points on the wall for the 4 fixing hole on the 

back plate. 

2. At the 4 marks, drill 4 holes (6mm in diameter) on the wall and 

    then push in the 4 plastic screw holders included with a hammer 

    (not included).  

3. Install the back plate to the 4 plastic screw holders with the 

    included 4 screws.

4. Connect and screw the 8~24VAC wire terminals to the 2 points of 17

    TP1and TP2 on the back plate. If no AC wires to be connected, 

    please skip this step. 

1. Install the back plate on to the door by inserting the 4 included 

    screws into the fixing holes on the back plate and screw tight to 

    the door.

Thank you for choosing this product. Firstly, please read this manual 

thoroughly to fully understand and make good use of this IP camera.

Open the package and make sure the device/ parts below are in good 

shape.

1. WiFi Doorbell X1

2. Wireless indoor bell receiver X1

3. Lithium ion batteries (type 18650) X2

4. Screw X1 + Hex wrench X1

5. Screw X4 + Plastic screw holder X4

1. WiFi connection for remote monitoring via internet.

2. Voice pairing, simple and reliable.

3. 720P HD video.

4. Lens of wide angle with panoramic view

5. Infrared light for night vision

6. Built-in mic. and speaker for two-way voice communication.

7. Support up to 64G TF (micro SD) memory card for video recording.

8. Bell detect: when the bell button is pushed, the device will give out 

an alarm signal with its related video to the user’s mobile phone. 

9. PIR human detection and notification: when the PIR detect a 

human motion, it will send out alarm message to the user’s mobile 

phone even if the APP doesn’t open.

10. Time-shift playback: easily and quickly allocate/ playback the 

desired video recorded at an elapsed time point by shifting the time 

axis. 

11. The device can be powered by rechargeable battery or 8~24V AC 

supply.

12. When use with a wireless indoor bell receiver, the bell receiver 

will emit an audio sound when the bell button is pushed to inform 

the home member to answer the door.  

13. The device is IP4 water resistant, can be installed without rain 

shelf.

14. Sleep mode for battery saving. It can be waked up by APP, PIR 

detection and push of the door bell button. After wake up, it will stay 

for 30 seconds and then enter the sleep mode again.  

      In the device list section, please click settings icon which at the 
top right corner to enter the device settings.2. Voice pairing, simple 
and reliable.

Accept call
Turn on - Receive the notification if somebody press the doorbell or 
call out.
Turn off - Will not receive the tifications for accept call.

Share QR Code
Send the QR code to share the device to your friends and family or 
someone that you want to share.

Delete camera
The mobile device will not receive the notifications after you delete 
the camera. But the camera still works and the other connected 
mobile devices still able to receive the notifications.

The device can support the PIR detection. Tap "PIR detection" to 
open the submenus.

Note: In crowded environment, it is recommended to close or set the 
           device to low sensitivity to reduce device arousal and call times 
           to extend battery life.

1.) The device is powered by rechargeable lithium batteries. With 
      fully charged, the battery life approx be six months. The mobile 
      device APP will be prompted while the battery voltage is low. 
      Please charge the device after received the reminder.
　

 

2.) Keep the camera in range of your router.
      Make sure to pick a place within range of your network. Thick or 
      insulated doors can greatly reduce the strength of your Wi-Fi 
      signal even if your router is close by, so you should try streaming 
      video before you mount your camera.
　

 

3.) The device is a low power consumption intelligent products, can 
      support remote wake up from the APP, PIR human detection, 
      press doorbell wake up. The device will be works for 30 seconds 
      after wake up then be in the resting state automatically and until 
      to next waking up.

Before you begin…
> Make sure the Ubell app is installed to your device.
> Make sure that your device is connected to a 2.4GHz Wi-Fi network, NOT a 5GHz 
   network.

UBell For iOS

UBell For Android

3.) Before setup, make sure the device is 
     in configuration --- with a voice prompt 
     "The camera is now ready to begin pairing".  

4.) If you didn't hear the voice prompt, press 
     and hold the reset button for 5 seconds. 
     Release after the LED indicator turnned 
     off , and the device will restart to configure 
     automatically.

中国移动

No

Do you hear ‘Camera  is now ready

to begin pairing’?

Yes

中国移动

Use the included pin to press

and hold the reset button for 5

seconds. The camera will notify

system reset.

7.) After a successful connection, you will be 
     prompted to create a name and password 
     for your camera. The password must be at 
     least 8 characters and include an uppercase 
     letter, a lower-case letter, and a number.

8.) Setup completed!  The APP will enter the 
     device list interface automatically. 
     Congratulations! The device is ready for use.

中国移动

Home

Password must be at least 8 characters and

include an uppercase letter, a lower-case letter,

and a number.

Select Wi-Fi

Search Camera

Add Camera

Finish

中国移动

Camera list

Add a camera

Home

中国移动

Camera settings

Delete camera

Accept call

Share QR Code

中国移动

PIR detection

Disabled

Low

Medium

High

The device will be able to wake up after device detects human 
for 7 seconds. Device start to take videos and call the mobile 
device at the same time.
The device will be able to wake up after device detects human 
for 5 seconds. Device start to take videos and call the mobile 
device at the same time.
In the state, the device will be able to detect if keep the state 
what be detected at least 1 second, and the device start to 
take videos and call to phones at the same time.

Low -

Medium -

High -

1. PIR sensor
2. Night vision LED’s
3. Light sensor
4. Lens of wide angle
5. Microphone
6. Button of door bell
7. Operation indicator
8. Top cover

9. Speaker
10. Contacts of 
      8V~24V AC souvce
11. Reset button
12. Anti stolen button
13. Micro USB charging port
14. Battery compartment 2X
15. Supporting hook,3X

16. Fixing hole 
      (4X) of back plate
17. Terminals of 
      8V~24V AC input,2X
18. Contacts of 
      8V~24V AC source
19. Water seal ring
20. Screw hole to fix main unit
21. Supporting hole 
      (3X) for main unit

Main unit

Main unit

Back plate

1

2
3

7

9

5

2

6

8

4

13

12

15

16

18

16

19

21
17

20

14

10

11

14

15

15

16

16

17

21

21

5.) The name of the Wi-Fi network will 
     automatically be filled in, enter the 
     Wi-Fi password. And adjust the volume 
     of your device to a reasonable level then 
     tap "Next". 

6.) The mobile device will emit sound waves, 
     keep quiet and make sure about 30cm 
    distance between the phone and the device , 
    and waitting for the device to configure the 
    network.
    If your camera fails to connect, reset the 
    camera and repeat all the steps(please see 
    the previous section, Resetting the Camera)

中国移动

Wi-Fi name

Wi-Fi password

Select Wi-Fi

Search Camera

Add Camera

Next

Connect to Wi-Fi

中国移动

Select Wi-Fi

Search Camera

Add Camera

Connecting

Connecting to WiFi...

4%

Note: If your mobile device was connected
to the same Wi-Fi network before, the APP
will fill the password auto matically and you
don’t have to  enter the password.

• Wirelessly activated by the signal from the intelligent door bell 

• 24 songs for selection to tell that an intelligent door bell is pushed

• 4 volume levels 

• Powered by a wall adapter/ charger with 5V DC output.

• The unit (the Indoor Wireless Bell Receiver) can be synchronized 

    with up to 4 different intelligent door bells. 

1. Clean the spot to where the unit is to be mounted

2. Peel off the protection paper on the Adhesive Pad 

3. Mount the unit by adhering the unit to the cleaned spot.

Connect a wall adapter/ charger with output of 1A or more to the 

micro USB power input port on the unit.

•  Synchronize the Unit with an Intelligent Door Bell

The unit can wirelessly work with an intelligent door bell forever 

once the unit is synchronized with the intelligent door bell. 

1. Power on the unit

2. Press and hold the Volume Control button on the unit

3. Push the button on the intelligent door bell

4. Release the Volume Control button on the unit when the unit 

    emits the song that responses to the push of the intelligent door 

    bell and the synchronization is complete.  

Power input port

(5VDC)

Singing indicator

Volum control button

Adhesive pad

Song selection button

Speaker

• Select a Song

Repeatedly press the SEL button to select a song that is to response 

to the push of the button on the intelligent door bell. 

• Adjust Volume

Repeatedly press the Volume Control button to adjust the volume. 

There are 4 volume levels. Each pressing on the button changes the 

volume level of the unit. 

 Upon power on, the volume is set at the highest level.  

Changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to operate 

the equipment.

This device complies with Part 15 of the FCC Rules. Operation is 

subject to the following two conditions: (1) this device may not cause 

harmful interference, and (2) this device must accept any 

interference received, including interference that may cause 

undesired operation.

This equipment has been tested and found to comply with the limits 

for a Class B digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from 

    that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with the FCC RF radiation exposure limits 

set forth for an uncontrolled environment. This equipment should be 

installed and operated with a minimum distance of 20 centimeters 

between the radiator and your body.

馬先生的-Intelligent WiFi door bell_20180629_说明书 size:80x130mm 正面  2018-11-14

 C

M

Y

K

Intelligent WiFi door bell_720P_说明书 size:80x130mm 反面  2018-11-15  

C

M

Y

K