Atomic Monkey Products Ltd. AMP10524T Manual Do Utilizador

1. Turn on the alarm base by moving the switch (Fig 1.) to the "ON" position 
2. Turn on each transmitter pod by moving the switch on the side of the pod to 

the "ON" position (Fig 1.)

3. Place each transmitter pod in a location where you expect movement to 

occur (hallway, kitchen counter, etc.). Position the pod's top arrow (silver 
color) pointed in the direction of movement. The pod's motion sensor must 
not be covered to allow it to trigger the base alarm. Note each pod has a 
number (pod #1 or pod #2). Remember where each pod is located!

 4. Take the base alarm unit with you anywhere within 75 feet (22.86 m) of the 

pod location and watch carefully to see if sensor 1 or sensor 2 alarm 
activates! The correct LED light will blink on the alarm base when there is 
any movement in front of the transmitter pod.

Hint: You can place pod #1 further away from you and Pod #2 closer to you

so you can track movement to see if it is coming toward you or going 
away from you!

Hint: You can also move the alarm switch (located near bottom of the alarm 

base unit) either to the silent mode (   ) if you only want a blinking light, or 
move it to the loudspeaker mode (   ) if you want an audible alarm to warn 
you of movement in front of the pod.

Tip: When finished playing with the Spy Tracker please turn off the transmitter 

pods and alarm base to save battery life!

Locate the end of the loop where it attaches to the base. To remove the end of the 
loop from the base, Rotate the ball-end downwards so that it can pull straight out 
from the socket. When the end is detached you can string each pod onto the loop 
for carrying or safekeeping. Close the loop by placing the ball-end back into the 
socket and rotating upwards into the locked position.

BATTERY SAFETY INFORMATION
· Only adults should install and replace batteries.
· Do not recharge non-rechargeable batteries.
· Remove dead or exhausted batteries.
· Insert batteries correctly. Match positive and negative signs.
· The supply terminals are not to be short circuited.
· Do not use rechargeable batteries.
· Do not mix alkaline, standard (carbon-zinc), or rechargeable

(nickel-cadmium) batteries.

· Do not mix old and new batteries.
· Only the batteries of the same or equivalent type recommended to be used.
· Do not dispose of batteries in a fire; they may explode.
· Dispose of batteries safely.

SPYX SPY TRACKER
10524-4000

Product specifications subject to change.

© 2015 Atomic Monkey Products, Ltd. Hong Kong, China, All rights reserved. 

Power

On/Off

Power

On/Off

Power

On/Off

Belt Clip

Battery Cover

Alarm

Base

Sensor

Alarm #1

Sensor

Alarm #2

Silent / Loudspeaker

Switch

Transmitter

Pod #1

Transmitter

Pod #2

Belt Clip

Release Tab

Battery Cover

Pod Holder Loop

Socket

Ball End

™

Mobile Early-Warning system!

SpyX Spy Tracker.
Base alarm requires two AAA (LR03) batteries, not included. 
Each transmitter pod receiver requires two AAA (LR03) batteries, not included 
(a total of four AAA batteries for both pods).
• Locate the belt clip on the bottom of the base alarm. To gain access to the
  battery cover, press the release tab on the belt clip and slide the belt clip
  toward the bottom end of the alarm base unit 
• Locate the battery door on the back of each transmitter pod and the
  alarm base (Fig. 3)
• Use a small Phillips head screwdriver to loosen the screw, and remove
  the battery cover (Fig.3).
• Remove all old batteries. 
• Place new batteries in compartments as shown (Fig. 3).
• Replace the battery covers and tighten screw and replace belt clip on
  alarm base.