Security People Inc. dba Digilock LO6I02NAO01 Manual Do Utilizador
SC-20-100D-10 Self-Contained RFID Latch
Operating Instructions
J-SC-20-1000-M_rev7 (PRE-PRODUCTION)
Page 1 of 4
Package Contents
SC-20-100D-10 Self-Contained RFID Latch (qty1)
Rotation Limiter (qty 1)
Cam Screw (qty 1)
Short Mounting Screw (qty 2)
Long Mounting Screw (qty 2)
Battery Box (qty 1)
(3 AA batteries not included)
(3 AA batteries not included)
Operating Instructions (qty 1)
SC-20-100D-10 Self-Contained RFID Latch
1.
Status Indicator
2.
Electronic Key Port
3.
Wake-up Button
4.
Knob
Features
Blue status indicator
Six second access time
Supports one SC-A10-10 programming key (order separately)
Supports up to six SC-A20-10 manager keys (order separately)
Supports up to 20 SC-A30-10 user keys (order separately).
Supports up to 20 RFID cards (order separately)
Express registration
Uses 3 AA batteries (not included)
Transmit frequency: 13.56MHz
Indoor use only
Battery Box
WARNING: Use only the included battery box to provide power to the
latch. The use of any other power supply may affect product functionality
and will void product warranty.
Contact Southco if a replacement battery box is needed.
and will void product warranty.
Contact Southco if a replacement battery box is needed.
Mounting and Installation
Please refer to Southco trade drawing J-SC-20-1000 for mounting and
installation details.
WARNING: The latch is shipped with both short and long mounting
screws. Be sure to use the appropriate mounting screw for the
latch’s
mounting cup and panel thickness, as shown below. See J-SC-20-1000
for additional details.
for additional details.
Power-on Sequence
When power is first applied to the latch, it will execute an internal power-on
sequence for approximately seven seconds. During this sequence, the
latch will not respond to the keys or wake-up button. The latch will emit a
wake-up beep when the sequence is completed, and respond normally
afterwards.
Low Battery Indicator
If the battery power supply is low, the latch will emit a pair of warning
beeps after access is granted. The batteries in the battery box should be
replaced.
Manager Key Battery Back-Up
In the event the battery power supply for the latch runs out, an assigned
manager key can still be used to open the latch. Contact an assigned
manager to the electronic key reader for approximately seven seconds.
The latch will unlock and the status indicator will flash for six seconds.
While the status indicator is flashing, turn the knob to open the latch. The
latch will re-lock after six seconds. Turn the knob to its original position to
secure the latch.
Demo Mode (prior to programming)
The latch is shipped without RFID cards or keys assigned. Before the
Programming Key is assigned, the latch will operate in demo mode by
pressing and holding the wake-up button.
NOTE: Once the latch has been programmed, this feature will not
work.
Programming the Latch
Initialize and Assign Programming Key and Manager Key(s)
(if no Manager Keys have been previously assigned)
Programming the Latch
Initialize and Assign Programming Key and Manager Key(s)
(if no Manager Keys have been previously assigned)
1.
Contact a Programming Key to the electronic key reader. This
will permanently assign the Programming Key to the latch.
will permanently assign the Programming Key to the latch.
panel thickness
mounting cup
mounting screw
1
– 5 mm
tall cup
(SC-20-xxx0)
short screw
>5
– 10 mm
>10
– 15 mm
long screw
>15
– 20 mm
short cup
(SC-20-xxx1)
short screw
>20
– 25 mm
long screw