NFTZ Hangpack Int'l Trading Co. Ltd. JS1-MK2 Manual Do Utilizador
4
Version 2.3 2014
1.0 Power Source and Installation:
1) Remote (Transmitter) – Is operated with one 12V 23/27A battery. (Included)
To install battery: Remove six screws from back of case, separate case and
install battery into holder. Snap case back together and reinstall six screws being
careful not to over‐tighten.
install battery into holder. Snap case back together and reinstall six screws being
careful not to over‐tighten.
2) Base (Receiver) ‐ Is operated with eight AA or eight C cell batteries. (Not included)
To install batteries: Loosen two screws on battery door and remove door.
Install desired batteries. (Note: if using AA batteries the four adapter tubes must
be used). Orient the batteries as per the directions shown in each cavity within
the holder. Note that the battery polarity alternates.
Install desired batteries. (Note: if using AA batteries the four adapter tubes must
be used). Orient the batteries as per the directions shown in each cavity within
the holder. Note that the battery polarity alternates.
3) Battery Carrier & Adaptor Tubes –
The battery carrier was designed as a removable component. The carrier can be
removed from the battery compartment and unplugged to separate it from the
unit.
removed from the battery compartment and unplugged to separate it from the
unit.
The battery carrier was designed to receive both C‐cell and AA batteries.
Base carrier is designed for C‐cell and by inserting AA batteries in the tube
adaptors; they will power the unit using the same carrier.
Base carrier is designed for C‐cell and by inserting AA batteries in the tube
adaptors; they will power the unit using the same carrier.
Note: For maximum performance use high quality batteries.
Tip: 1) Be prepared… pack replacement batteries and a coin or straight
screwdriver in your game caller bag.
2) To prolong battery life in cold conditions, hand warmers can be used
between the ground and battery door to radiate heat to the batteries.
screwdriver in your game caller bag.
2) To prolong battery life in cold conditions, hand warmers can be used
between the ground and battery door to radiate heat to the batteries.
2.0 Caller Operation:
1) Power on
a) For Base unit, switch On/Off Rocker to the on position.
b) For Remote, there is no on / off button: just press button for desired function.
The Remote only consumes power from the internal battery when a button is
pressed.
b) For Remote, there is no on / off button: just press button for desired function.
The Remote only consumes power from the internal battery when a button is
pressed.
2) Power Off
a) Switch On/Off rocker to the off position on the base unit. Remote needs no
shut down.
shut down.
3) Selecting sound to be played (sounds are designed to start softly and increase in
volume then fade out when stopped)
volume then fade out when stopped)
a) Simply press the numeric key of the sound that is desired, i.e., If you want to
play sound one, simply press the 1 key. To play sound 21, simply press the 2 then
1 keys, etc. A sound reference card has been supplied, listing the 25 sounds that
are pre‐loaded.
b) If a sound with a single digit numeric key is selected, there will be a 2 second
delay in the sound starting. This is due to the system waiting for the second digit
if a two digit numeric key is required.
c) If you select a new sound while a sound is playing, the new sound will replace
the current one as the audible sound and the original will stop.
play sound one, simply press the 1 key. To play sound 21, simply press the 2 then
1 keys, etc. A sound reference card has been supplied, listing the 25 sounds that
are pre‐loaded.
b) If a sound with a single digit numeric key is selected, there will be a 2 second
delay in the sound starting. This is due to the system waiting for the second digit
if a two digit numeric key is required.
c) If you select a new sound while a sound is playing, the new sound will replace
the current one as the audible sound and the original will stop.
4) Stop a sound(s)
a) Press the “Stop” button on the remote when you want to stop the current
audible sound.
audible sound.