Shenzhen Fatshark Co. Ltd. FSV1251 Manual Do Utilizador
www.fatshark.com
UltraMicro FPV Camera Operation manual/specification REV A
Overview:
The UltraMicro FPV camera is a micro VGA imager paired with digital to analog converter and micro transmitter
for use with ultralight RC airframes. Its 1S (3.5-4.5) volt input is designed to share onboard power supply with the
micro craft (commonly powered off 1S lipo packs). The camera has DC-DC step up regulator to ensure proper
operation even if supply voltage drops due to air frame demand. Low power transmitter allows for FCC license
free use and is suitable for indoor and short range performance.
The UltraMicro FPV camera is a micro VGA imager paired with digital to analog converter and micro transmitter
for use with ultralight RC airframes. Its 1S (3.5-4.5) volt input is designed to share onboard power supply with the
micro craft (commonly powered off 1S lipo packs). The camera has DC-DC step up regulator to ensure proper
operation even if supply voltage drops due to air frame demand. Low power transmitter allows for FCC license
free use and is suitable for indoor and short range performance.
Electrical:
Power supply: 3.3-5.5V (1S supply)
Power consumption: 300mA @ 3.7V (1S)
Imager:
1/6” VGA CMOS
Lens:
0.95mm
0.95mm
IR cut
115
115
ediagonal FOV (90ehorizontal)
Operation:
-10 to 60C
Mechanical:
Square: 13.2 X 17.6 X 9mm
Lens extrude: 9mm X 10mm diameter
Antenna extrude: 20mm X 25mm diameter
Lens extrude: 9mm X 10mm diameter
Antenna extrude: 20mm X 25mm diameter
Weight:
3.5g
Packaging
Dimensions: bag 50 x 70 mm
Weight: (approximately 16g)
Weight: (approximately 16g)
System:
Analog NTSC video out
Interface:
Single push button channel control
(1-7 then back to ch 1)
2p male 1.25mm JST (power, ground)
(1-7 then back to ch 1)
2p male 1.25mm JST (power, ground)
Indicators:
Solid LED for noting power on
Channel select LED flashes on channel change
(Channel LED is solid on channel 1 only)
Channel select LED flashes on channel change
(Channel LED is solid on channel 1 only)
Operating
Frequencies:
5740 MHz, 5760 MHz, 5780 MHz, 5800 Mhz, 5820 MHz 5840 Mhz 5860 MHz
Operation
When power is applied (3.3 – 5.5V) the camera and transmitter are powered. The camera has memory so the
transmitter will power up in the last used channel. The top LED shows the camera has power and the lower LED
flashes when channel is changed (by depressing button). The channels scroll sequentially from ch 1-7 (and back
to 1). Only on channel 1 is the channel indicator a solid light.
transmitter will power up in the last used channel. The top LED shows the camera has power and the lower LED
flashes when channel is changed (by depressing button). The channels scroll sequentially from ch 1-7 (and back
to 1). Only on channel 1 is the channel indicator a solid light.
Detailed Operation
Image is focused onto the 1/6” digital imager via the 0.95m lens. The lens has an IR filter to condition the light
entering the imager to optimize image color. The camera board has an A/D conversion circuit that converts the
VGA digital imager signal into an NTSC analog signal. The analog signal is transferred to the transmitter PCB
and the RF circuit encodes the modulated analog signal onto the 5.8 Ghz carrier signal. The 5.8Ghz carrier
signal is sent up the 50 ohm impedance antenna line to the antenna. The antenna is tuned to resonate at 5.8Ghz
and the signal is transmitted into open space to be received by a compatible receiver.
entering the imager to optimize image color. The camera board has an A/D conversion circuit that converts the
VGA digital imager signal into an NTSC analog signal. The analog signal is transferred to the transmitter PCB
and the RF circuit encodes the modulated analog signal onto the 5.8 Ghz carrier signal. The 5.8Ghz carrier
signal is sent up the 50 ohm impedance antenna line to the antenna. The antenna is tuned to resonate at 5.8Ghz
and the signal is transmitted into open space to be received by a compatible receiver.