Mediabridge Products LLC BTS-1B Manual Do Utilizador

1: Please use attached USB charging cable in the package to charge unit

2: Please disconnect charge cable after full charged the unit , Do not charge the unit 

    for long time after unit full charged

3: Do not immerse the product in water and seawater

4: Do not use and leave the product near a heat source as fire or heater

5: Do not place it into water , any other liquid ,Fire or any heater machine .

6: Do not strike or throw the product.

1: 

Do not use or leave the product at very high temperature (for example, at strong 

    direct sunlight or a vehicle in extremely hot conditions).Otherwise, it can overheat 

    or fire or its performance will be degenerate and its service life will be decreased.

2: Do not  use  it  in  a location  where static electricity is great, otherwise, the safety 

    devices may be damaged, which will cause hidden trouble of safety.

3: The batteries should be stored at room temperature, charged to about 30% to 50%

 

    

of capacity. In case of over-discharge, batteries should be charged for one time 

    every

  month  while  storing and batteries should be discharge and charge after 

    being stored more than a year in order to activate it and restore energy.

4: Please following Waste battery recycling method to dispose the unit 

This product bears the selective sorting  symbol  for waste  electrical and 

electronic equipment (WEEE).

This means  that  this  product  must  be  handled  pursuant  to  European 

Directive 2002/96/EC in order to be recycled or dismantled to minimize its 

impact on the environment.

For further information, please contact your local or regional authorities.

2h

-Rechargeable Speaker

-3.5mm audio cable

-Micro USB Charging cable

-User guide 

1. Use the included USB Charging cable , Plug one end into the DC 5V jack located 

at the bottom of the unit , Plug the other end into a USB powered port or any other 

USB AC adapter (not included). 

2. The battery is fully charged in 1.5 hours .(Charging time will be longer if play music 

    while charging .) 

3. The red LED light indicates that the unit is charging , The red LED turns off when 

the battery is fully charged ,You can disconnect the charging cable when charging is 

complete.

Please read the manual carefully before use

and keep it well for further use

i

 

Bluetooth mode :

Search Status :Blue LED flash slowly

Successful pairing: Blue lights flash 2 times every 5 seconds 

Line in mode : 

Blue LED light stay on 

Charging mode : 

Red LED indicates the unit is charging and not full

Red LED will turn off when fully charged 

 

NOTE:The product is designed for use with Bluetooth 

wireless devices compatible with the HFP,HSP,A2DP 

and  AVRCP  streaming  audio  profiles. Refer  to  your 

Bluetooth device’s user manual  or  technical  support  to 

determine if your Bluetooth device supports these profiles.

STOP

Before you make a call with the unit, you need to pair and link your Bluetooth-enabled

 

phone with the 

unit. Please refer to Pairing procedure 

1. To answer a call, press the         Button. Now you can use the unit as a speaker 

    phone.

2. Speak into the MIC  and press the vol- or vol+ Button on the unit to adjust the call 

    volume.

3. To end the call, press the         Button.

NOTE :  When the sound becomes distorted  or  LED light flashing , the battery  is 

low and needs to be recharged, Please volume up your mobile volume and speaker 

volume if handfree voice is low.

5. Press the vol- or vol+ Button on the unit to adjust the system volume.

6. Press        button to pause/play music

NOTE : When the sound becomes distorted or LED light flashing , the battery is low 

and needs to be recharged

 . 

1. Plug one end of the included 3.5mm audio cable into the headphone or line-out 

    jack of your audio device.

2. Plug the other end of the cable into the LINE IN jack located on the back of the unit.

3. Slide the power switch of the speaker to ON position. 

4. Turn on your audio device and play music .Make sure your audio device is charged

 

    and turned to medium volume.

4. Adjust the volume of your audio device to the desired level.

5. Press the vol- or vol+ Button on the unit to adjust the system volume.

6. Slide the power switch to the off position when you are finished listening. You may 

also turn off your audio device.

NOTE : The speaker is powered by a Lithium-ion rechargeable battery, if you start to 

notice sound  distortion or the LED is flashing, the battery  is low and needs  to be 

recharged.

    

If  you are using  a Bluetooth audio device, make sure the working distance is 

 within 20 - 30 ft, different environment  may have effect on the working distance.
1. Slide the power switch of the speaker to ON position, The unit will give a beeping 

    sound to indicate it is in Bluetooth mode.

2. Turn on the Bluetooth on your audio device 

3. Searching Devices Choose "ProMini X11".No password is required.If your device 

    does 

require a password,type”0000”

4. Adjust the volume on your audio device to the desired level.

   If at any time in the future you should need to dispose of this product please note 

that Waste electrical products should not be disposed of with household waste.Please

recycle where facilities exist.Check with your Local Authority or retailer for recycling

advice.(Waste Electrical and Electronic Equipment Directive)

VOL+

VOL  

 

1: Aux In-put Jack 

2: Function Indicates LED

3: Micro USB Charge Jack

4: Power ON/OFF 

DC 5V

LINE-IN

ON/OFF

1

3

4

2

1

2 3 4

VOL+

VOL  

1: Handfree/Play/Pause Button

2: Volume-

3: MicroPhone

4: Volume+

BTS-1B