IONIT Networks LLC ION9071 Manual Do Utilizador
9-5573-03
IONIT Networks LLC
5600 Post Rd, Suite 114, Unit 225
East Greenwich, RI 02818
(401) 244-7404
www.ionitnetworks.com
Site Installation Instructions for No. 9500
Version 1.1 – 5/23/2014
Prior to beginning installation of the IONIT components at a home or business location, please read through the entire set of instructions
and verify that you have all of the items needed for a successful installation. Note: Prior reading of VisiTank document titled “Tips for
Successful VisiTank® Field Installation” is strongly recommended prior to attempting an installation.
Successful VisiTank® Field Installation” is strongly recommended prior to attempting an installation.
The VisiTank
®
system by IONIT Networks is designed to provide remote monitoring capabilities
of liquid levels in storage tanks. Typical applications include fuel, water, chemicals and waste
oils.
oils.
(1) No. 9070 or 9071 Ultrasonic Sensor/Transmitter w/screws
(2) No. 7020 2” NPT Tank Adapter (1½”, 1¼” and others available by special order)
(3) No. 9400 Broadband Internet Hub
(4) No. 9420 USB DC Power Supply Adapter for Hub (Not shown)
(5) No. 9430 Ehternet Cable-7ft for Hub (Not shown)
18” Pipe Wrench to remove tank plug (3-4ft length of 2” pipe may be needed)
Thread Sealant for 7020 Tank Adapter
Screw Driver (Philips or Slotted) to fasten Sensor to Tank Adapter
Smart phone with Internet connectivity
The VisiTank
®
system has been rated as (Class II) equipment degree (2). It is designed to
operate under the following environmental conditions: (a) Indoor use, (b) Temperature 40°F to
104°F, (c) Maximum relative humidity of 80% for temperatures up to 88°F, decreasing linearly
to 50% relative humidity at 104°F.
Hub:
Sensor:
The Sensor is powered by a 3V DC Lithium cell battery, CR2430, which should last 10+ years
The Sensor is powered by a 3V DC Lithium cell battery, CR2430, which should last 10+ years
under normal circumstances. Replacement battery instructions are listed on the Sensor label.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
P1. Prepare the tank by removing one of the tank plugs and installing the appropriate Tank
Adapter. Note the fuel level. If the Sensor must be mounted on a raised manhole cover or
nipple, it must be at least 3” diameter. Measure the distance from the top of the tank to the
“VisiTank” logo label on the Sensor. Record this value in the Sensor Offset box on the
Installation Form.
P2. Select a suitable final location for the Hub. A power outlet and an open available network
connection on the consumer’s router are needed.
1. Install Hub: Connect the USB power supply securely to the Hub. The OK (top) and Power (bottom) LED indicators on the Hub will light
Green and the Status (middle) LED will flash Red to indicate that the device is ready.
2. Activate Sensor: Now activate the Sensor by placing a magnet next to the black dot on the Sensor’s label for ~30 seconds. The Status
LED on the Hub will blink.
3. Install Sensor: Using the pipe wrench remove a tank plug. Thread the 2” NPT Tank Adapter into the plug hole. Secure the Sensor to
the Tank Adapter using the gasket and screws provided.
4. GeoLocate Hub: Using your smart phone, scan the QR code on the 9400 Hub (also found on the box). When prompted log into your
IONIT account (click “Remember Me”). Click ‘Get Current Location’ to use your phone’s GPS to get your position (ensure your GPS is
turned on), and then input other identifying details such as Customer ID or a Customer Label (e.g. Mr. Jone’s House).
5. GeoLocate Sensor: Using your smart phone, scan the QR code on the 9070 rocket sensor (also found on the box) and repeat the details
in instruction #4.
6. Verify Tank Level: Using your smart phone, scan the QR code found on the 9070 Sensor to view the current tank gauge level.
Installation has been successful!
Components Included in No. 9500 VisiTank® Kit
Tools and Optional Test Equipment
Intended Use of Equipment
Preparation
Technical Specifications
Risk of
electrical
shock
shock
The hub is powered by a UL listed Class 2 power supply; (input: 100-240 VAC, 200mA, 47-63Hz– Output: 4.5-9.5
VDC, 800mA), and connects to the consumer’s broadband Internet router with a standard RJ45 connector.
Replacement power supply (#9420) is available from IONIT Networks LLC.
Installation Steps
(1)
(2)
QR Code Label
Magnet
Location for
Activating
Sensor
(3)
OK LED
STATUS LED
ETHERNET PORT
POWER LED
POWER PORT
STATUS LED
ETHERNET PORT
POWER LED
POWER PORT