Atoms Labs LLC ADR42R Manual Do Utilizador

Do not touch live electrical parts. 
Electric shock can be avoided. Follow the 

recommended practices listed below. Faulty 
installation, improper grounding, and incorrect 

operation and maintenance of electrical 
equipment are always sources of danger. 

Do not try to install equipment outdoor, during 
strong wind and rain. 

Do not install or remove equipment outdoor, 
when raining. 

Do not try to install or operate any equipment, 
during a thunderstorm. 

Always ground all electrical equipment and the 
work platform. 

Prevent accidental electrical shocks. Connect 

power source, control cabinets, and work 
platform to an approved electrical ground. 

Always use the correct cable siz e. 
Sustained overloading will cause cable failure 

and result in possible electrical shock or fire 
haz ard. Work cable should be the same rating 

as the factory. 

Always keep cables and connectors in good 
condition. Improper or worn electrical 
connections can cause short circuits and can 

increase the chance of an electrical shock. Do 

not use worn, damaged, or bare cables. 

Always avoid open-circuit voltage. 
The added voltages increase the severity of 
electric shock haz ard. 

Always wear insulated gloves while you adjust 
equipment. 

Electric power should be turned off and 
insulated gloves should be worn when making 

any equipment adjustment to assure shock 
protection. 

Always wear protective clothing such as long 
sleeve shirts while you are installing or  

removing equipment. 

Always wear high, snug fitting shoes. 

Always wear clean clothes without grease or oil. 

Protect neighboring workers from exposure to arc 
radiation. 

Always wear long trousers or jeans while you are 
installing or removing equipment. 

Always wear safety helmet or hard head and safety 
shoes before work. 

Always keep the equipment in dry places. 

Always wear safety harnesses/belt while you work 
in high places. 

Always wear dry clothing and avoid moisture and 
water. 

Always wear Public Safety Vest, while you work at 
night. 

Make sure all electrical connections are tight, clean, 
and dry. 

Make sure that you are well insulated to eliminate 
electric static charge. 

Always wear dry gloves, rubber-soled shoes, or 
stand on a dry board or platform. 

Always follow recogniz ed safety standards. 

Always wear correct eye, ear, and body protection. 

Always have second person on-site, while you work 
in dark, poor ventilation, or high  places. 

Make sure that you are well protected against arc 
flashes, mechanical injury, or other mishaps. 

Make sure that the polarity of wire is correct before 
installing equipment. 

Always handle equipment with care. 

Do not block the ventilation of equipment. 

Do not put the magnetic parts around the equipment. 

Do not put the objects on top of the equipment. 

 

5. Next on HDD setup check 

the status of the hard drive. 

If it shows as “Formatted” 

then it is ready to be used. 

If not, select drive and click 

“Format.” Click “Done” 

to finish the setup. 

If you are having an issue 

connecting to the internet 

please double check the 

cat5e cable and make sure it 

is plugged to the router or 

modem correctly. 

1. Now power up all the 

cameras and wait about 

30~90 sec to see if all the 

cameras are connected. 

(Double-click left mouse to 

change between single and 

multi-camera.)
(If you have an issue with 

a connected camera please

refer to our troubleshooting 

section on page 18)

2. Once you verify that 

the cameras are connected

and working, you may install

them in the desired locations 

(screws included).

It is a good idea before 

mounting cameras to make 

sure they are within range 

of NVR.

2. Y You may scan the QR 

3. Set date and time. Click 

“apply,” then “next.” 

code using a QR code 

reader to download a 

mobile app to your phone 

— or skip to the next step 

and download the application

when finished with the setup.

1. Once you have connected

the power adapter wait for 

the system to start up. 

Right-click mouse and 

select setup wizzard. 

When you see the log-in 

screen, click OK and 

setup wizard will appear.

4. Next you will be asked for 

an internet connection. 

If you have already

connected the cat5e cable,

network status will be 

shown as “

Healthy

”. 

If you have not connected 

the cat5e cable, you may 

do so now and click “auto 

config” to refresh the status.

 

(This step is required for remote viewing)

 

1. If you have not yet

downloaded the

applications you may do

so now. Please go to the

“App Store” or “Play Store” 

and search for “IP PRO” 

and install.

2. Once the installation is 

finished, open the IP PRO 

and  touch “Register” to

make a new account.
(If you have already

registered please log in and

skip to step 4)

3. Please input a user name

and password (6~12

characters) and type the

password one more time

to confirm. Once you have

finished, touch register and

you will get a pop-up

message to verify email. 

Please enter your email

and

  ”.

y

fi

r

e

v

“ 

h

c

u

o

t 

4. When you have logged in

touch the “+ ” on top right 

and “Add device by ID”

5. Touch the     icon to start 

the QR scanner. 

6. Y ou can find the QR code 

under (System setup >

Netowrk setup > Network 

setup > show QR code).
Now scan the QR code

using the app scanner and

it will automatically input 

the “Cloud ID” for you.

 

1. If you have not yet

downloaded the

applications you may do

so now. Please go to the

“App Store” or “Play Store” 

and search for “IP PRO” 

and install.

2. Once the installation is 

finished, open the IP PRO 

and  touch “Register” to

make a new account.
(If you have already

registered please log in and

skip to step 4)

3. Please input a user name

and password (6~12

characters) and type the

password one more time

to confirm. Once you have

finished, touch register and

you will get a pop-up

message to verify email. 

Please enter your email

and

  ”.

y

fi

r

e

v

“ 

h

c

u

o

t 

4. When you have logged in

touch the “+ ” on top right 

and “Add device by ID”

5. Touch the     icon to start 

the QR scanner. 

6. Y ou can find the QR code 

under (System setup >

Netowrk setup > Network 

setup > show QR code).
Now scan the QR code

using the app scanner and

it will automatically input 

the “Cloud ID” for you.

Page 1

Page 2

1. Power up the NVR using 

the provided 3 Amp power 

adapter within the package 

and plug it into the DV12V 

port on back of the device

2. Connect the USB mouse 

next to the power port on

the back of the device.

3. Connect the Cat5e (LAN) 

cable to the NVR and plug 

the other end to the 

internet router or modem 

for internet connection. 

(This step is require for remote viewing)

 

  

 

  

(required for recording)

If the NVR does not have a Hard Drive, for first time use please install an 

internal SATA II or III 3.5” hard drive with steps below:

Remove the NVR screws of NVR case

 Connect the SATA HDD cable and power line

Attach the hard drive to the bottom of the NVR as shown below

Close the cover and replace cabinet screws

Page 4

Page 5

Page 6

Page 7

7. On the descriptions you

can leave it as blank or

enter the location

information. (ex: home, office)

Default

User name: admin

Password: (blank)

Now touch submit to finish.

8. Now you can see the

newly added list on the

main page. Now you can

touch the image and start

the live view.

9. Within the live view you

can choose the video

quality by touch “Stream”

and choose between

“SD” (low quality) or

“HD” (High quality).

Y ou can also take a snap

shot or record short clips

and save in the phone to

to view them later.

11. Y ou can select the

channel you want to

play back using the “CH”

icon on bottom right and

select the channel. Once

you have selected the

channel, time line will

appear and you can slide

left-to-right and select the

time fr ame.

 

Split Screen 

Choose between x1 or x4 view  

Video Manage 

Sync or add new IP camera 

System Setup 

Configure NVR system setting 

Video Playback  Quick play back of 5, 10, 30 min or 

manual search 

Video Backup 

Backup recorded file to USB Flash 
Drive 

Color Adjust 

Adjust hue, brightness, saturation, 
and contrast 

PTZ Control 

Bring up digital PTZ controller for PTZ 
cameras (PTZ camera not included) 

Manual Record  Force the system to record 24/7 

Volume

N/A

Setup Wiz ard 

Step by step setup guide 

System Mode 

N/A 

Fast Network 

Quick setup for  network connection 

Wifi Add 

NVR Wifi information  

Exit System 

Log out, Reboot, Close Screen output, 
and Shutdown 

10. Y ou can also view

recorded video remotely

using the “playback”

button.

1. Using the internet explorer

go to “www.e-seenet.com”.

Once you are at the log-in

screen click on “Username

login.”

2. If you have not already

made an account. click on

“New account.” to make a

new account. If you have

made an account using the

smartphone application

use the same ID/Password

to log in to the website.

3. Once you log in it will ask

you to add device. If it

does not show

automatically, go to

(system setup > setup

wiz ard). Now click on “Add

device” and enter in all the

required information, which

can be found in the (NVR

system setup > Network

setup).

If you have already add

device skip to # 4.

4. When you finish, click on

“Live Online.” On the

right side you will be able

to see the device you just

added.

5. Under the camera list click

on “Open All” to start the live 

remote view.When you’re done 

viewing click on the “Exit” to log

out.

NOTE: CMS Program is 

available for easy access 

from computer using 

Windows & Mac. For details 

refer to CMS guide. 

Page 8

Changes or modifications not expressly approved by the party responsible for compliance 

could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential installation. This 

equipment generates uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the 

user is encouraged to try to correct the interference by one or more of the following 

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following 

two conditions (1)this device may not cause harmful interference, and (2) this device must 

accept any interference received, including interference that may cause undesired 

operation.

The distance between the product and body is more than 20cm