Yellowstone Technology Ltd. Taiwan branch BT1 Manual Do Utilizador
YellowStone Technology Ltd. -
香港商陽碩利華有限公司台灣分公司
OEM Installation Manual
Record No. & Ver.: R705-04 , V1.0
Yellowstone Technology Ltd.
Tel: +886 4 2350 9590 Fax. +886 4 2350 9591
Initial Relase date: 27 Nov 14
Made by: Steve Lin
Printed: 27-Nov-14
File name: Bluetooth Module BT1 OEM Installation Manual for CB2 and RMC V1.0
- 27 Nov 14.doc
5 頁，共 6 頁
This document can not be copied, reproduced nor given to third parties without written authorization of Yellowstone
3. Inspection
3.1. A visual inspection should be performed to assure that all components soldering pad are not short circuit.
3.2. A visual inspection should be performed to assure that the U1” shield is at horizontal center, and fix well.
4. Packaging
4.1. PCBA should be packed individually.
5. FCC Statements
In accordance with FCC Part 15C and RSS-210, this module is listed as a Modular Transmitter device.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
the equipment.
The antenna of this transmitter must not be co-located or operating in conjunction with any other antenna or
transmitters within a host device, except in accordance with FCC multitransmitter product approval procedures.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
the equipment.
The antenna of this transmitter must not be co-located or operating in conjunction with any other antenna or
transmitters within a host device, except in accordance with FCC multitransmitter product approval procedures.
6. FCC Label Instructions
The outside of final products that contains this module device must display a label referring to the enclosed module.
This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: 2ACRR-BT1”
Or
“Contains FCC ID: 2ACRR-BT1”
Any similar wording that expresses the same meaning may be used.
Additionally, there must be the following sentence on the device, unless it is too small to carry it:
“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.”
If the final product is to be sold in Canada, then this exterior label should use wording such as the following:
“Contains Transmitter Module IC: 12172A-BT1”
This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: 2ACRR-BT1”
Or
“Contains FCC ID: 2ACRR-BT1”
Any similar wording that expresses the same meaning may be used.
Additionally, there must be the following sentence on the device, unless it is too small to carry it:
“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.”
If the final product is to be sold in Canada, then this exterior label should use wording such as the following:
“Contains Transmitter Module IC: 12172A-BT1”
7. IC Statements
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.