Hangzhou Hikvision Digital Technology Co. Ltd. I002U40 Manual Do Utilizador

Appearance

*使用产品前请仔细阅读快速操作指南，并妥善保管

Name

Description

IR Light

LED

Indicator

Auto light source for night vision. The light is

behind the anti-reﬂection panel. You can see the

light when it is on.

RESET/WPS WPS: Set Wi-Fi connection via WPS (Wi-Fi

Protected Setup) function.

RESET: Hold down the button for 10 seconds

when the camera is starting up or rebooting.

Memory

Card Slot

For microSD card. If a memory card is used,

video ﬁles will be stored in the memory card.

You would need to initialize it via the

Hik-Connect app/web browser/client software.

Steady red: The camera is starting up.

Flashing blue: The camera is on and ready for

the Wi-Fi connection.

Steady blue: The camera is running properly.

Flashing red: Network exception.

Network Cube Camera

Quick Start Guide

Regulatory Information
FCC Information
Please take attention that changes or modiﬁcation not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the

interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is

connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the

radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause

undesired operation.
EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE"

and comply therefore with the applicable harmonized European standards listed

under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU, Radio

Equipment Directive 2014/53/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed

of as unsorted municipal waste in the European Union. For proper recycling, return

this product to your local supplier upon the purchase of equivalent new equipment,

or dispose of it at designated collection points. For more information see:

www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be

disposed of as unsorted municipal waste in the European Union. See the product

documentation for speciﬁc battery information. The battery is marked with this

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to a designated

collection point. For more information see: www.recyclethis.info.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna

of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To

reduce potential radio interference to other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut

fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour

l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain

de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité

nécessaire à l'établissement d'une communication satisfaisante.
This equipment should be installed and operated with a minimum distance 20cm between the

radiator and your body.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur

et votre corps.

Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject

to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Safety Instruction
These instructions are intended to ensure that a user can use the product correctly to avoid

danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.

Warnings: Follow these

safeguards to prevent serious

injury or death.

Cautions: Follow these

precautions to prevent potential

injury or material damage.

Warnings

● Proper conﬁguration of all passwords and other security settings is the responsibility of the

installer and/or end-user.

● In the use of the product, you must be in strict compliance with the electrical safety

regulations of the nation and region. Please refer to technical speciﬁcations for detailed

information.

● Do not connect several devices to one power adapter as adapter overload may cause

over-heating or a ﬁre hazard.

● Please make sure that the plug is ﬁrmly connected to the power socket. When the product

is mounted on wall or ceiling, the device shall be ﬁrmly ﬁxed.

● If smoke, odor, or noise rise from the device, turn oﬀ the power at once and unplug the

power cable, and contact the service center.

● Make sure the power supply voltage is correct before using the camera.

● Do not drop the camera or subject it to physical shock.

● Do not touch sensor modules with ﬁngers. If cleaning is necessary, use a clean cloth with a

bit of ethanol and wipe it gently. If the camera will not be used for an extended period,

replace the lens cap to protect the sensor from dirt.

● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur

(which is not a malfunction), and aﬀect the sensor’s endurance at the same time.

● The sensor may be burned out by a laser beam, so when any laser equipment is in use,

make sure that the surface of sensor will not be exposed to the laser beam.

● Do not place the camera in extremely hot, cold (the operating temperature shall be -10°C to

+50°C), dusty, or damp locations, and do not expose it to high electromagnetic radiation.

● To avoid heat accumulation, ensure that there is good ventilation to the device.

● Keep the camera away from liquids.

● While in delivery, pack the camera in its original, or equivalent, packing, packing materials.

Or packing of the same texture.

● Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be

replaced regularly according to their average endurance. The average time varies because of

diﬀerences between operating environments and usage history, so regular checking is

recommended for all users. Please contact your dealer for more details.

● Improper use or replacement of the battery may result in hazard of explosion. Replace with

the same or equivalent type only. Dispose of used batteries according to the instructions

provided by the battery manufacturer.

● If the product does not work properly, please contact your dealer or the nearest service

center. Never attempt to disassemble the camera yourself. (We shall not assume any

responsibility for problems caused by unauthorized repair or maintenance.)

Cautions

Name

Description

For the power supply, (12V ). Plug the

power cable into the power input interface to

power on the camera.

Power

Input

RESET/WPS

Install the camera.

Paste the mounting template onto the

installation surface.

Quick Start Guide
COPYRIGHT ©2016 Hangzhou Hikvision Digital Technology Co., Ltd.

Any and all information, including, among others, wordings, pictures, graphs are the properties

of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be

“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced,

changed, translated, or distributed, partially or wholly, by any means, without the prior written

permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,

guarantees or representations, express or implied, regarding to the Manual.
About this Manual
The Manual includes instructions for using and managing the product. Pictures, charts, images

and all other information hereinafter are for description and explanation only. The

information contained in the Manual is subject to change, without notice, due to ﬁrmware

updates or other reasons. Please ﬁnd the latest version in the company website

(http://overseas.hikvision.com/en/).
Visit the company website (http://overseas.hikvision.com/en/) to get the manuals, client

software, and developing tools.
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgment
and other Hikvision’s trademarks and logos are the properties of Hikvision in

various jurisdictions. Other trademarks and logos mentioned below are the properties of their

respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH

ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND

ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT

LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR

PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS

DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,

DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR

DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE

WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR

ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER

ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;

HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR

JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE

CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS

PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE

LATER PREVAILS.

IR Light

Status

Indicator

Lens

MIC

Bracket

Speaker

Power

Interface

Memory Card Slot

Install memory card (optional).

Unscrew the cover to expose the memory

card slot.

Installation

Insert the memory card.

(Optional) to unmount the memory card, push

to get it ejected.

Screw the cover back.

Align the screw holes on mounting surface

with those on the bracket. Fix the bracket with

three screws.

Drill three screw holes according to the

template.

Pry the bracket open at the “OPEN” sign.

Remove the trim ring.

Trim Ring