PHIMAX INTERNATIONAL LIMITED MMA3632 Manual Do Utilizador

2 3 4 5

7 8 9

AC/USB Adaptor

Battery Recharging:

NOTES:

Top View:

Side View:

1. Open the rubber cover on the right of unit as the illustrated on right.

The unit has a built-in Li-ion rechargeable battery,

recharge it before first time use or when it is consumed as follows.

3. Connect the AC/DC Adaptor to a wall outlet

having AC 100-240V, 50/60Hz as the illustrated on right.

2. Connect the small plug from the supplied AC/DC Adapter to the DC IN Jack.

4. During charging, the Red Charging Indicator will illuminate.

When finished charging, the color of the Charging Indicator will turns to Green.

• The adrubber cover is for water and dust resistance; always make sure it is completely closed after open.
•   This AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position.
•   To save energy, unplug the AC/DC Adaptor from the wall outlet if you will not use it for an extended period of time.
•   During charging, you can also play and listen music from the unit at the same time.

Your battery will last longer if you following these simple guidelines for charging and storing.

A. Before first time use, recharge the unit approximate 4 hours until the unit was fully recharge.

B. Recharging and store the unit within the temperature range of 5°C - 35°C (40°F - 95°F).

C. Do not overcharge (longer than 24 hours). Excessive charging or running the

unit until battery goes empty will damage battery. Battery life will be

extended if you keep the battery fully charge.

D. Battery life naturally shortens slowly over time.

E. The rechargeable battery incorporated in this product is not user replaceable.

8. Charging Indicators

9. USB Port (For Charging External USB Device)

10. AUX In Jack

11. Carry Handle

12. Rubber Cover (This cover is for water and

dust resistance; always make sure it is

completely closed after open)

1. Indicators

2. Button

3. Button

4. + Button

5. – Button

6. Built-in Microphone

7. DC IN Jack (For Charging)

CHARGING THE EXTERNAL USB DEVICE VIA USB PORT

TROUBLESHOOTING

SPECIFICATTIONS:

LIMITED WARRANTY

PACKAGE INCLUDES:

NORMAL OPERATION AFTER PAIRED:

IMPORATANT:

Check the following before requesting service:

NOTES:

OPERATION

IMPORTANT SAFETY INSTRUCTIONS

BT (BLUETOOTH):
BT PAIRING:

In first time use or re-pairing the unit to a new BT Device, pairing it as below:

1.Power on the unit by press and hold the Button on the top of unit approximate 1 second. The unit will enter to BT

(Bluetooth) mode automatically and the Blue Indicator on the top of unit will illuminate and blink.

2.Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from

the external BT Device. After paired, the Blue Indicator will stop blinking.

3.Plays the music in the paired BT Device as usual.

4.During playback:

Press and release the Button to pause: press again to resume normal playback.

Press and hold the + or - Buttons to adjust volume level as desire.

Press the + or - Buttons repeatedly to skip tracks.

5.If the unit is paired to a Cell Phone and a call is incoming during music listening, press and release the

Button to pause the music playback then speak to the built-in Microphone to answer the call. When your call is

complete, press and releases the Button to hook on and resume to music playback.

6.To shut off the unit, press and hold Button approximate 3 seconds until the Indicator is not light.

When the external BT Device searched the unit, our model number “MMA3632” will appear on the display of

external BT Device.

Pairing code “0000” or “1234” may need to enter.

1.Power on the unit by press and hold the Button on the top of unit approximate 1 second. The unit will enter to BT

(Bluetooth) mode automatically. The Blue Indicator on the top of unit will illuminate and blink.

2.Wait a few seconds until the unit auto paired to the external BT Device. (The Blue Indicator will stop blinking).

3.Plays the music in the paired BT Device as usual.

AUX IN

To play music from an external Audio Player via a 3.5mm audio out jack:

1.Power on the unit by press and hold the Button on the top of unit approximate 1 second.

The unit will enter to BT (Bluetooth) mode automatically. The Blue Indicator on the top of unit

will illuminate and blink.

2.Connect one end of the supplied Audio Connection Cable to the AUX Out; Line Out; Phone Jack

from the external audio player.

3.Open the rubber cover on the right of unit.

4.Connect the other end to the AUX In Jack on the rear of unit.

5.Press the Button on the top of unit to enter to AUX In mode, the color of the Indicator will

turns to Green.

6.Plays the music on the external Audio Player as usual. (Make sure the audio out of the Player

was set to high. Otherwise, sound form this unit will be weak).

7.During playback, press and hold the + or - Buttons on the unit to adjust the sound level as desire.

8.To shut off the unit, press and hold Button approximate 3 seconds until the Indicator is not light.

The unit equipped a built-in USB Charger. Use it to charging the external USB device as

follows:

2. Connect the suitable plug from the USB Connection Cable (Not included) to the

charging port on the external device you wants recharge as the illustrated follows:

3. Charging will auto start. Monitoring the charging status through the external device as usual.

4. When finished, unplug the USB Connection Cable from both units.

A.Before charge the external device, check the power of the built-in battery. If the power of the

unit is too low, it cannot charge the external device.

B.The power of the built-in battery is 2200 mAh only. Do not use it to recharge the external device

which has powerful built-in battery (more than 2200 mAh). It will caused the external device

cannot be fully charge by this unit.

C.The unit has a built-in overload/overheats protector. If the output of the unit is overload (or

short circuit). The built-in charger will auto shut off.

SYMPTOM

POSSIBLE CAUSE

POSSIBLE SOLUTION

Can’t power on

Recharge the battery as page 3

Volume of the unit was set to minimum

position

Increase the volume by press and

hold the + Button

Volume level of paired/connected

device is in low level

Rise the volume level of

the paired/connected device

No sound or sound

weak

Sound distortion

Volume level too high

Reduce the volume level by press

and hold the - Button

Built in battery consumed

Volume level of the connected/paired

device too high

Reduce the volume level of the

connected/paired device

BT not functioning

The external BT Device had NOT

paired to the unit

Pair the external BT Device to the

unit as page 4

The external BT Device too far from

the unit

Place the external BT Device close

to the unit

Power source: Built-in DC 7.4V, 2200 mAh (16.28 WH) rechargeable Li-ion Battery,

Recharge by DC 9 V, 2 A through DC IN Jack

Dust/water resistance level: IP66
Output of the built-in Charger:

DC 5 V, 1A

Impedance of the speakers:

2 x 10 W; 4 ohm

Audio power:

2 x 8 W (Total 16 W, RMS)

BT Version:

4.0

BT Operation Distance:

96 Feet in opera area

1x Use’s Manual

1x AC/DC Adapters (Input: AC 100-240V~; 50/60Hz; Output: DC 9V, 2A)

1x Audio Connection Cables with 3.5mm Stereo Plugs

1. Open the rubber cover on the right of unit.

CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT

REMOVE THE COVER (OR BACK). NO USER SERVICEABLE

PART INSIDE, REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Berore using the unit,be sure yo read all operating

instructions carefully.Please note that these are general

precautions and may not pertain to your unit. F or exanple,

this unit may not have the copability to be connected to an

outdoor anyenna.

The lighting flash with arrowhead symbol ,within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s

enclosure, that maybe of sufficient magnitude to constitute

a risk of electric.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

.Read these instructions

All the safety and operating instructions should be read

before the appliance is operated.
2

.Keep these instructions

The safety and operating instructions should be kept for

future reference.
3

.Heed all warnings

All warnings on the appliance and in the operating

instructions should be adhered to.
4

.Follow all instructions

All operation and use instructions should be followed.
5

.Do not use this apparatus near water

The appliance should not be used near water; for example,

near a bath tub, washbowl, kitchen sink, laundry tub, in

awet basement, or near a swimming pool.
6.

Clean only with dry cloth

The appliance should be cleaned only as recommended by

the manufacturer.
7

.Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Slots and openings in the cabinet and in the back or bottom

are provided for ventilation, to ensure reliable operation of

the product and to protect it from overheating. These

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or similar surface. This product should never be

placed near or over a radiator or heat source. This product

should not be placed in a built-in installation, such as a

bookcase or rack unless proper ventilation is provided or

the manufacturer’s instructions have been adhered to.

8.Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9.Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10.Product the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11.Only use attachments / accessories specified by the manufacturer.

12.Use only with a cart, stand, tripod, bracket,

or table specified by the manufacturer,

or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

An appliance and cart combination should be moved

with care. Quick stop, excessive force and uneven

surfaces may cause the appliance and cart

combination to overturn.

13.

Unplug this apparatus during lightning

storms or when unused for long periods of

time.

To protect your product from a lightning storm, or

when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect

the antenna or cable system. This will prevent damage

to the product due to lightning and power-line surges.

14.Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

15.

Power source

This product should be operated only from the type of

power source indicated on the marking label. If you

are not sure of the type of power supply to your

home, consult your appliance dealer or local power

company. For products intended to operate from

battery power, or other source, refer to the operation

instructions.

16.

Power lines

An outside antenna system should not be located in

the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep

from touching such power lines or circuits as contact

with them might be fatal.

17.

Overloading

Do not overload wall outlets and extension cords as

this can result in a risk of fire or electric shock.

18.

Object and liquid entry

Never push objects of any kind into the product

through openings as they may touch dangerous

voltage points or short out parts that could result in

fire or electric shock. Never spill or spray any type of

liquid on the product.

19.

Outdoor antenna grounding

If an outside antenna is connected

to the product, be sure the antenna

system is grounded so as to provide

some protection against voltage surges

and built up static charges. Section 810

of the National Electric Code ANSI/ NFPA 70 provides

information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-

in wire to an antenna discharge product, size of

grounding conductors, location of antenna-

discharge product, connection to grounding

electrodes and requirements for the grounding

electrodes.

20.

Service

Do not attempt to service this product yourself as

opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

21.

Replacement parts

When replacement parts are required, be sure the

service technician uses replacement parts specified

by the manufacturer or those that have the same

characteristics as the original parts. Unauthorized

substitutions may result in fire or electric shock or

other hazards.

22.

Safety check

Upon completion of any service or repairs to this

product, ask the service technician to perform safety

checks to determine that the product is in proper

operating condition.

23.

Wall or ceiling mounting

The product should be mounted to a wall or ceiling

only as recommended by the manufacturer.

24.

Damage requiring service

A.Unplug this product from the wall outlet and refer

service to qualified service personnel under the

following conditions.

B.When the power- supply cord or plug is damaged.

C.If liquid has been spilled or objects have fallen into

the product.

D.If the product has been exposed to rain or water.

E.If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions, as an adjustment of other controls

may

result in damage and will require extensive work by

a qualified technician to restore the product to its

normal operation.

F. If the product has been dropped or the cabinet has

been damaged.

G.When the product exhibits a distinct change in

performance- this indicates a need for service.

25.

Note to CATV system installer

This reminder is provided to call the CATV system

installer' s attention to Article 820- 40 of the NEC

that provides guidelines for proper grounding and,

in particular, specifies that the cable ground shall be

connected to the grounding system of the building,

as close to the point of cable entry as practical.

NOTE: Refer all servicing to qualified service personnel.

Servicing is required when the unit has been damaged

in any way such as the following: the power-supply cord

or plug has been damaged, liquid has been spilled into

unit, the unit has been exposed to rain or moisture, the

unit has been dropped or the unit does not operate

normally.

Craing warrants this prsduct to be free from manufacturing defects in material and

workmanship under normal use for a period of 90 days from date of purchase.If service

is required,please retu the product to the store where it was purchased for exchange;

or,pack the unit in the original packing material with accessories if applicable,a copy

of your sales receipt and a Cashies’s check or Money Order for $7.00 (to cover shipping

and handing costs) payable to Craig Electeonics Inc.For consumers in Canada,please

make sure that the cashier check or money order is redeemsble through a U.S.bank.

Ship your product freight pre-paid.Your unit will be repaired, replaced,replaced or if the unit can

not be repaired or replaued,a refund will be forwarbeb to you within four weeks of receipt of

your unit. Plerse ship your unit to:

This warranty is void if the product has been:a)Used in a commercial application or

rental.b)Damaged through misuse, negligence, or abuse. c) Modified or repaired by

anyone other than an authorized Craig service center. d) Damaged because it is

improperly connected to any other equipment.

Note: This warranty does not cover. a )Ordinary adjustments as outlined in the Owner’s

Manual which can be performed by the customer. b)Damage to equipment not properly

connected to the product. c) Any cost incurred in shipping the product for repair. d)

Damage to the product not used in the USA.

This warranty is not transferable and only applies to the original puruchase. Any implied

warranties, including the warranty of merchantability, are limited in duration to the period

of this expressed warranty and no warranty whether exprssed or implied shall apply to

the product thereafter.

Under no circumstance sall Craig be liable for any loss or consequential damage arising

out of the use of this product. This warranty gives specific legal rights rights. However, you may

have other rights which may bary from state to state. Some states do not allow limitations

on implied warranties or exclusion of consequential damage. Therefore, these

restrictions may not apply to you.

To Obtain Service on your Product

email:service@craigelectronics.com

Printed in China

Craig Electronice Inc.

1160 NW 163 Drive

Miami,FI 33169

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

WARNING: USE UNDER SUPERVISION OF AN

ADULT DUE TO LONG CORD

This unit has a long cord that can be easily tripped

on or pulled on, causing injury. Please make sure it

is arranged so that it will not drape over a

tabletop, etc. Where it can be pulled on by

children or tripped over accidentally.

FCC NOTICE:

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and

can radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

l Reorient or relocate the receiving antenna.

l Increase the separation between the equipment

and receiver.

l Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

l Consult the dealer or an experienced radio/TV

technician for help.

FCC STATEMENT:

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any interference

received, including interference that may cause

undesired operation. The antenna(s) used for this

transmitter must be installed to provide a

separation distance of at least 20 cm from all

persons and must not be co-located or operating

in conjunction with any other antenna or

transmitter.

FCC WARNING:

To assure continued operation, follow the

attached installation instructions and use only

shield cables when connecting to other devices.

Changes or modifications not expressly approved

by the party responsible for compliance could

MMA3632

Bluetooth Speaker

MAGNAVOX

PHIMAX INTERNATIONAL LIMITED

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by manufacturer could void your
authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement.