JVC HMHDS4 Manual Do Utilizador
Masterpage:Right-NoTitle0
69
Filename [HM-HDS4EK_06Edit.fm]
Page 69
April 22, 2003 10:12 pm
L-2 SELECT and L-2 INPUT Setting
Set “L-2 SELECT” and “L-2 INPUT” to the appropriate mode
depending on the type of appliance connected to the recorder’s
L-2 IN/DECODER connector.
depending on the type of appliance connected to the recorder’s
L-2 IN/DECODER connector.
A
Select the input mode for the L-2 IN/
DECODER connector.
DECODER connector.
A Press
rt
to move the arrow to “L-2 SELECT”, then
press OK.
B Press
rt
to select the appropriate setting, then press
OK.
* The default setting is bold in the table below.
B
Return to the normal screen.
Press MENU.
NOTES:
● If you have a satellite receiver or a decoder connected to the
L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back
to appropriate mode after editing.
to appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to
the L-2 IN/DECODER connector, leave “L-2 SELECT” set to “A/
V”.
V”.
● The default setting is “A/V”; if the recorder’s memory backup
has expired due to a power cut or because the AC was
removed from the recorder, “A/V” will be automatically
selected when the power is restored to the recorder. If you are
using a satellite receiver or a decoder, be sure to set “L-2
SELECT” back to appropriate mode.
removed from the recorder, “A/V” will be automatically
selected when the power is restored to the recorder. If you are
using a satellite receiver or a decoder, be sure to set “L-2
SELECT” back to appropriate mode.
● When “L-2 SELECT” is set to “SAT”, “SAT” appears on TV
screen or front display panel instead of “L-2” or “L2”.
● If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set
“L-2 SELECT” to “DECODER”.
F-1 INPUT Setting
Set “F-1 INPUT” to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
connector (VIDEO or S-VIDEO) being used on the front panel.
A
Select the input mode for the VIDEO/S-
VIDEO connector.
VIDEO connector.
A Press
rt
to move the arrow to “F-1 INPUT”, then
press OK.
B Press
rt
to select the appropriate setting, then press
OK.
* The default setting is bold in the table below.
B
Return to the normal screen.
Press MENU.
Perform steps
A and B of “L-1 OUTPUT and L-1 INPUT
Setting” on page 68.
8
L-2 SELECT
A/V
:
To use this recorder as the recording
deck with the player connected to
the L-2 IN/DECODER connector, or
to use the satellite receiver
connected to the L-2 IN/DECODER
connector.
deck with the player connected to
the L-2 IN/DECODER connector, or
to use the satellite receiver
connected to the L-2 IN/DECODER
connector.
DECODER:
To use a decoder connected to the
L-2 IN/DECODER connector.
L-2 IN/DECODER connector.
SAT:
To view a satellite programme with
the TV set while the recorder is
turned off. (
the TV set while the recorder is
turned off. (
墌
pg. 76)
8
L-2 INPUT
VIDEO
:
If a connected appliance’s output is
compatible only with regular video
signals, set to “VIDEO”.
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO:
If a connected appliance’s output is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain
high-quality S-VHS picture. (For
connection, be sure to use a 21-pin
SCART cable that is compatible with
the Y/C signal.)
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain
high-quality S-VHS picture. (For
connection, be sure to use a 21-pin
SCART cable that is compatible with
the Y/C signal.)
Perform steps
A and B of “L-1 OUTPUT and L-1 INPUT
Setting” on page 68.
8
F-1 INPUT
VIDEO
:
When connecting an appliance to
the VIDEO input connector, set to
“VIDEO”.
the VIDEO input connector, set to
“VIDEO”.
S-VIDEO:
When connecting an appliance to
the S-VIDEO input connector, set to
“S-VIDEO”.
the S-VIDEO input connector, set to
“S-VIDEO”.
HM-HDS4EK.book Page 69 Tuesday, April 22, 2003 10:14 PM