Philips Stubble and beard trimmer QT4019/15 QT4019/15 Folheto

w

 Fully charge Trimmer before using for the first  

  time or after non-use for a long period of time.

w

 Battery performance is best if you recharge   

  only when the battery is (almost) completely  

  empty.

w

 Charging, recharging, or using the Trimmer at  

 temperatures below 40˚F or higher than 95˚F

  adversely affects  lifespan of the battery.

w

 Continuously recharging Trimmer will reduce  

  lifespan of battery.

   

1 

Be certain Trimmer is OFF (fig. 1). 

Insert the appliance plug directly into the   

   Trimmer (fig. 2) and plug the adaptor into any 

   120V AC outlet. Use only the cord provided.

w

 An adaptor plug may be necessary for 

  cord usage in some foreign countries. Use  

  an attachment plug adaptor of the proper  

  configuration for power outlet.   

The Charging Light on the appliance will light  

   to indicate the Trimmer is charging. 

w

 It will take approximately 10 hours to fully   

  charge the Trimmer for a cordless trimming   

 time of up to 35 minutes.

NOTE: After the Trimmer is fully charged, the 

Charging Light will remain lit.

Disconnect the cord and unplug from 

   electrical outlet.

w

  After the Trimmer has been charged for 

the first time, do not recharge the Trimmer 

between trimming sessions. Continue using it 

until the battery is completely empty.

w

 Do not charge for more than 24 hours.

w

 Do not keep cord permanently plugged in.

w

 Discharge/run down the battery completely   

  twice a year by letting the motor run until it   

  stops.

w

 If the Trimmer hasn’t been used for a long   

  period of time, it must be recharged for a full  

  10 hours. 

 

w

Only use the Trimmer corded when the 

  battery is empty.

w

Trimmer does not recharge during corded 

  trimming. 

Connect cord provided to Trimmer and plug 

   Trimmer into electrical outlet. 

If battery is completely empty, wait a few 

   minutes before switching Trimmer ON.

 3 

Slide ON/OFF switch ON to begin trimming.

 

  Turn Trimmer OFF and unplug.

Charge according to directions. Unplug   

   Trimmer from outlet and remove cord. 

Slide ON/OFF switch ON to begin trimming.

If the charge runs out while trimming, simply 

   connect cord provided to Trimmer and outlet  

   to continue trimming.

w

 Use this Trimmer for its intended household  

use as described in this manual.

w

 Always comb the beard and/or moustache with 

a fine comb before you start trimming.

w

 If you are trimming for the first time, be 

careful. Do not move the Trimmer too fast. 

Make smooth and gentle movements.

w

 Guide Comb Attachment must be on Trimmer 

  in order to use the Zoom Lock.

 

  Turn the Zoom Lock to the desired trimming 

   length setting (see table). The setting will  

   appear in the window below the Zoom Lock  

   (fig. 3).

w

 If you are trimming for the first time, start by 

  using the maximum trimming length setting   

  (#9) to prevent accidentally trimming hairs too  

  short. As you become familiar with the settings,  

  adjust Zoom Lock to desired trimming length.  

  Zoom Lock will “click” into position at each  

  setting.

  Make sure the Trimmer is switched OFF   

   and disconnected from the electrical outlet.

 

  Remove the Guide Comb Attachment.

 

  Open the cutting unit (fig. 9).

 

  Clean the cutting unit and the inside of the  

   Trimmer with the brush supplied (fig. 10).

 

  Push the cutting unit back into place on the 

   Trimmer until you hear a click (fig. 11). 

 

If your cutters become damaged or worn, 

do not continue using the Trimmer. Replace 

cutters immediately.

 

  Open the cutting unit.

 

  Remove the old cutting unit by pulling it   

   upwards (fig. 12).

  Place the two notches of the new cutting   

   unit into the guiding slots (fig. 13).

 

  Push the cutting unit back onto the Trimmer  

   until you hear a ‘click’.

 

This Trimmer has no other user-serviceable

parts. For assistance call 1-800-243-3050.

For assistance, visit our website: 

Information is available 24 hours a day,  

7 days a week.

w

 Be sure Trimmer is turned OFF. Remove cord  

  from outlet and Trimmer before storing in a  

  safe, dry location where it will not be crushed,  

  banged, or subject to damage.

w

 Do not wrap cord around Trimmer when   

  storing.

w

 Store cord in a safe location where it will not  

  be cut or damaged. 

w

 Do not place or store Trimmer where

  it can fall or be pulled into a tub or sink, water  

  or other liquid.

w

This Philips Norelco Trimmer contains a 

  rechargeable Nickel Metal Hydride battery  

  which must be disposed of properly (fig. 14).

w

Battery should only be removed when Trimmer 

  is to be discarded.

w

For assistance, call toll free: 1-800-243-3050 or

  visit our website, www.philips.com/support.

Unplug electrical cord from outlet and 

   Trimmer before dismantling Trimmer. 

 

  Allow Trimmer to run until the battery is 

   empty/depleted. 

 

  Turn Trimmer OFF.

 

  Use a screwdriver to remove the housing of 

   the Trimmer (fig. 15). 

 

  Separate the housing parts with a 

   screwdriver (fig. 16). 

 

  Cut the wires close to the battery holder 

   with household scissors (fig. 17). 

 

  Remove the battery holder with the 

   rechargeable battery (fig. 18). 

 

  Use a screwdriver to pry the battery off the 

   printed circuit board (fig. 19). 

 

  Do not attempt to replace battery.  Insulate 

   battery ends by covering with tape and/or  

   place battery in a small plastic bag. 

 

  Discard your Trimmer.  Do not attempt to 

   plug electrical cord into the outlet or  

   recharge the Trimmer after the battery has  

   been removed. 

 

  Contact your local town or city officials 

   for battery disposal information or call  

   1-800-8-BATTERY or www.rbrc.com for  

   battery drop-off locations.

 

  Switch the Trimmer ON.

 

  To trim in the most effective way, move the  

   Trimmer against the direction of hair growth.  

   Make sure the surface of the comb always   

   stays in contact with the skin (fig. 4).

NOTE: Since all hairs do not grow in the 

same direction, you may want to try different

trimming positions (i.e., upwards, 

downwards, or across). Practice is best for 

optimum results. 

  If cut hairs have accumulated in the Guide 

   Comb, turn Trimmer off, remove the Comb  

   Attachment and blow and/or shake the  

   hair out of the comb (fig. 5). The selected  

   trimming length setting will not change  

   when you do this.

Never pull off the Guide Comb Attachment 

by grasping the flexible top portion. Always 

pull off by the bottom part of attachment.

 

 

 

 

 

 

 

 

 

 

 

 

 

  Be certain Guide Comb is on Trimmer   

   and use setting #1 to result in a “stubble”   

   look (fig. 6).

 

Remove Guide Comb Attachment if you are:

w

 Defining hair lines

w

 Trimming nape of neck

w

 Removing single, unwanted hairs

 

  Be certain Trimmer is in the OFF position.

 

  Remove the Guide Comb Attachment by   

   pulling it off the Trimmer (fig. 7).

 

  Switch the Trimmer ON.

 

  Make well-controlled movements. Touch the  

   hair lightly with the Trimmer (fig. 8).

Be careful when you are trimming without comb 

attachment as when the Trimmer is turned on it 

will trim every hair it touches.

 

w

 Clean the comb attachment after each use.

w

  Always switch Trimmer OFF, unplug and remove 

power supply cord from Trimmer before 

cleaning.

w

 Do not use compressed air, abrasive cleaning  

  agents, scourers or liquids such as alcohol,  

  benzene, bleach or acetone to clean the   

  Trimmer and attachments.

w

  Never clean, replace or remove Trimmer comb 

with motor ON.

w

  Never rinse or immerse the Trimmer in water 

or any other liquid.

w

  Do not apply pressure to cutters.

w

 Do not touch cutters with hard objects as this  

  may damage them. 

w

 Use a soft, dry cloth to clean Trimmer handle.

w

 If cut hairs have accumulated in the Guide 

  Comb area, turn Trimmer off, pull Guide Comb  

  Attachment off Trimmer and remove hairs by  

  shaking and/or blowing.

When using an electrical appliance, basic safety 

precautions should always be followed, including 

the following: 
Read all instructions before using this 

To reduce the risk of electric shock: 
1.  

Do not reach for a trimmer that has fallen 

into water. Unplug immediately.

2.  

Do not use while bathing or in a shower.

3.  

Do not place or store trimmer where it can 

fall or be pulled into a tub or sink. Do not 

place in or drop into water or other liquid.

4.  

Always unplug this trimmer from the 

electrical outlet immediately after using, 

except when trimmer is (re)charging.

5.   Unplug and remove power supply cord from

trimmer before cleaning.

shock or injury to persons: 
1.  

Close supervision is necessary when  

this appliance is used by, on, or near children 

or invalids.

2.  

Use this trimmer for its intended household 

use as described in this manual. Do not use 

attachments not recommended by Philips 

Electronics North America Corporation. 

3.  

Never operate this trimmer if it has a  

damaged cord or plug, if it is not working  

properly, if it has been dropped, damaged, or 

dropped into water. For assistance call  

1-800-243-3050.

4.  Do not rinse or immerse the trimmer in 

  water or any other liquid.

5.   Keep the trimmer, cord and any attachments

away from heated surfaces.

6.  

Never drop or insert any object into any 

opening.

7.  

Do not operate, charge or plug in trimmer 

outdoors or where aerosol (spray) products 

are being used or where oxygen is being 

administered.

8.  

Always check cutters, cutting unit and comb 

before using the trimmer. Do not use the 

trimmer if cutters, cutting unit or comb are 

damaged, as injury may occur.

9.   Always attach plug to trimmer first, then

to outlet. To disconnect, turn on/off switch 

to “OFF” position, then remove plug from 

outlet.

10.  To prevent possible damage to the cord, do 

not wrap cord around the trimmer.

11.  Never put trimmer in direct sunlight or store 

at a temperature above 140°F.

12.  This trimmer is for use on human hair only. 

Do not use this trimmer for any other  

purpose.

13.  Always store your trimmer, attachments and 

power plug in a moisture-free area. Make 

sure the cord is disconnected from the 

trimmer.

14.  Only use the power plug supplied with the 

appliance. 

 

See Battery Removal Instructions.

Congratulations on your purchase and welcome 

to Philips Norelco!

To fully benefit from the support that Philips 

Norelco offers, register your product at 

www.philips.com/norelco 

A  Guide Comb Attachment

B  Cutter Blades

C   Precision Patented Zoom Lock with 9 Pre-

Select Settings

D  Charging Light

E  Socket for Appliance Plug

F  On/Off Switch

G  Adaptor

H  Appliance Plug

I  Cleaning Brush

  Full Two-Year Warranty

 45-Day Money-Back Guarantee

 

 

 

 

 

 

 

 

 

 

 

 

 

Like many new products, your Philips

  Norelco 

Stubble Trimmer

 may take a little getting used to. If 

you are using an electric Trimmer for the first time, 

or if you’ve been using a different brand, take the 

time to acquaint yourself with your new Trimmer.

 

Your Trimmer features an unique stubble look 

setting combined with an adjustable Zoom Lock to 

make beard trimming goof-proof. 

 

Throw your scissors away and put your new 

 

Trimmer to the test. We guarantee precise, 

professional results or Philips

  Norelco will 

refund you the full purchase price as long as the 

request is received within 45 days of purchase. 

 

If you are not fully satisfied with your Philips 

Norelco Trimmer, send the product back along 

with dated sales receipt and we’ll refund you 

the full purchase price.

To obtain Money-Back Guarantee Return 

Authorization Form, call 1-800-243-3050 for 

assistance. Please allow 4-6 weeks for delivery 

of check.

4222 002 8025 3

Philips Electronics North America Corporation warrants each new Philips 

Norelco product, Model QT4021, QT4019 against defects in materials or 

workmanship for a period of two years from the date of purchase, and 

agrees to repair or replace any defective product without charge.

IMPORTANT: This warranty does not cover damage resulting from 

accident, misuse or abuse, lack of reasonable care, the affixing of any 

attachment not provided with the product or loss of parts or subjecting 

the product to any but the specific voltage.* Use of unauthorized 

replacement parts will void this warranty.

In order to obtain warranty service, simply go to www.philips.com/

norelco or call 1-800-243-3050 for assistance. It is suggested that for 

your protection you return shipments of product by insured mail, 

insurance prepaid. Damage occurring during shipment is not covered by 

this warranty. 

NOTE: No other warranty, written or oral, is authorized 

by Philips Electronics North America Corporation. This warranty gives 

you specific legal rights, and you may also have other rights which vary 

from state to state. Some states do not allow the exclusion or limitation 

of incidental or consequential damages, so the above exclusion and 

limitations may not apply to you.

*Read enclosed instructions carefully.

Manufactured for: 

Philips Consumer Lifestyle

A Division of Philips Electronics North America Corporation 

P.O. Box 10313, Stamford, CT 06904

Norelco is a Registered Trademark of Philips Electronics 
North America Corporation.

Zoom Lock is a Trademark of Philips Electronics North America Corporation.

PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N.V.

© 2010 Philips Electronics North America Corporation. All Rights Reserved.

Register your product and get support at

 

www.philips.com/norelco

QT4019
QT4021 

Rechargeable 

Cordless/Cord

Stubble 

Trimmer

 

#1  Stubble Length

#2 

#3

#4

#5 

#6 

#7 

#8

#9 

 

3/64 in/1mm

 

5/64 in/2mm

              9/64 in/3.5mm

 

3/16 in/5mm

 

9/32 in/7mm

 

3/8 in/9mm

     

29/64 in/11.5mm

         19/32 in/14.5mm

 

23/32 in/18mm

9

9

(Model  

QT4021 Shown)

10_QT4019_21.indd   1

10/29/10   9:22 AM