Adtran OC-3 CWDM SFP 1491nm 1442701PG2 Folheto
Códigos do produto
1442701PG2
C A U T I O N
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Warranty:
ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at
©2010 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442701PG2-22C*
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the userʹs authority to operate this equipment.
could void the userʹs authority to operate this equipment.
CAUTION
C
The SFP OC3 contains a Class 1 laser that complies with the Laser
Safety requirements of FDA 21 CFR 1040.10 and 1040.11, and EN
60825‐1, and ‐2. The SFP OC3 is NRTL Listed and CB Certified to
all applicable American and European safety standards.
Safety requirements of FDA 21 CFR 1040.10 and 1040.11, and EN
60825‐1, and ‐2. The SFP OC3 is NRTL Listed and CB Certified to
all applicable American and European safety standards.
CAUTION
!
♦
Per GR‐1089‐CORE Section 9, the SFP OC3 does not have an
internal DC connection between battery return and
frame ground.
frame ground.
♦
The ADTRAN system that the SFP OC3 is being deployed in is
designed and intended for installation as part of a Common
Bonding Network (CBN), or Isolated Bonding network (IBN).
Bonding Network (CBN), or Isolated Bonding network (IBN).
♦
The SFP OC3 can be installed in a DC‐I (isolated) or DC‐C
(common) configuration. For installations where other cards
or the host system have internal connections between battery
return and frame ground, the system would be intended for
deployment only in a DC‐C configuration.
or the host system have internal connections between battery
return and frame ground, the system would be intended for
deployment only in a DC‐C configuration.
♦
The ADTRAN system chassis frame ground terminal must be
connected to a reliable earth ground to ensure that the metal
enclosure of the SFP OC3 is properly grounded via the
backplane connector.
connected to a reliable earth ground to ensure that the metal
enclosure of the SFP OC3 is properly grounded via the
backplane connector.
NOTE
♦
The OC‐3 port(s) are optical and therefore are not classified as
any type of port as defined in Appendix B of GR‐1089‐CORE
Issue 5.
Issue 5.
♦
This SFP OC3 is compliant with SFF‐8472 “Digital Diagnostics
Monitoring Interface for Optical Transceivers,” Revision 9.3.
♦
This SFP OC3 is compliant with the Small Form‐Factor
Pluggable (SFP) Multi‐Source Agreement (MSA).
♦
This product is designed to be deployed in GR‐3108‐CORE
environment class 1 or 2 as defined in GR‐3108‐CORE issue 2.
The SFP OC3 is designed to meet the following environmental
classes:
classes:
♦
ETSI EN 300 019‐1‐1 “Classification of environmental
conditions; Storage,” Class 1.2
conditions; Storage,” Class 1.2
♦
ETSI EN 300 019‐1‐2 “Classification of environmental
conditions; Transportation,” Class 2.3
conditions; Transportation,” Class 2.3
♦
ETSI EN 300 019‐1‐3 “Classification of environmental
conditions; Stationary use at weather‐protected locations,”
Class 3.3
conditions; Stationary use at weather‐protected locations,”
Class 3.3
♦
ETSI EN 300 386 “Electromagnetic compatibility and Radio
spectrum Matters (ERM); Telecommunication network
equipment; Electromagnetic Compatibility (EMC)
requirements”
spectrum Matters (ERM); Telecommunication network
equipment; Electromagnetic Compatibility (EMC)
requirements”
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.3.
during exposure to all test severities per Class 3.3.
www.adtran.com
for further infor‐
mation on RoHS/WEEE.