Transition Networks SCSCF3015-100 SCSCF3015-100-NA Folheto
Códigos do produto
SCSCF3015-100-NA
Stand-Alone
Specifications
Standards
ANSI, ITU-TS, ETSI, AT&T, G.703, G.921 & G.955
Coax Connectors
75 ohm coax
TX output
RX input
min: +2.5 dBm
min: -9.7dBm
max: +9.1 dBm
max: +10.5 dBm
Fiber Connectors
SFP: LC connector Uses standard 100BASE-X/OC-3 SFP
Data Rates
DS3/T3 = 44.7 Mbps; E3 = 34.4 Mbps;
STS-1 = 51.8 Mbps
Status LED
Power, Coax link status, coax loop-back status, AIS on
coax link; Fiber link status, fiber loop-back status,
AIS on fiber link
Dimensions
Width: 3.25” [83 mm];
Depth: 4.7” [119 mm];
Height: 1.0” [25 mm]
Power Consumption
3.0 Watts
Power Supply
12 VDC, 0.8 Amp (minimum)
Environment
Operating Temperature -10° to 65°C (14° to 149°F)
Humidity 5-95% non-condensing
Storage Temperature -20º to 85ºC (-4º to 185ºF)
Shipping Weight
2.0 lbs. [0.90 kg]
Regulatory Compliance
CISPR/EN55022 Class A; FCC Class A; CE Mark
MTBF w/ Power Supply
Greater than 41,660 hours (MIL-HDBD-217F)
Greater than 114,580 hours (Bellcore)
MTBF w/o Power Supply Greater than 250,000 hours (MIL-HDBD-217F)
Greater than 687,000 hours (Bellcore)
Warranty
Lifetime
SCSCF30xx-11x
SCSCF30xx-11x
stand-alone network interface device
DS3-T3/E3 and STS-1 Coax to Fiber
DS3-T3/E3 and STS-1 Coax to Fiber NID
see also:
DS3-T3/E3 Point System™ Slide-In-Module NID
The DS3 – T3/E3 & STS-1 copper to fiber network
interface device (NID) provides a solution for those
users that need to extend DS3 connections over
fiber.
The DS3 – T3/Es & STS-1 supports Small Form Plug-
gable (SFP) transceivers to support a variety of fiber
types, distances and wavelengths to provide maxi-
mum flexibility across a variety of network topolo-
gies. The use of Coarse Wave Division Multiplexing
(CWDM) SFPs can be utilized to further increase the
bandwidth capacity of the fiber infrastructure.
The DS3 – T3/E3 & STS-1 NID must be used in
pairs*. A typical installation will include a chassis
card [CCSCF, pg 55] installed in the Point Sys-
tem™ locally and a stand-alone device installed at
the remote location.
interface device (NID) provides a solution for those
users that need to extend DS3 connections over
fiber.
The DS3 – T3/Es & STS-1 supports Small Form Plug-
gable (SFP) transceivers to support a variety of fiber
types, distances and wavelengths to provide maxi-
mum flexibility across a variety of network topolo-
gies. The use of Coarse Wave Division Multiplexing
(CWDM) SFPs can be utilized to further increase the
bandwidth capacity of the fiber infrastructure.
The DS3 – T3/E3 & STS-1 NID must be used in
pairs*. A typical installation will include a chassis
card [CCSCF, pg 55] installed in the Point Sys-
tem™ locally and a stand-alone device installed at
the remote location.
DS3-T3/E3
Optional Accessories (sold separately)
Wide Input (24 - 60 VDC) Power Supplies
SPS-2460-PS
Piggy Back Power Supply
SPS-2460-SA
Stand-Alone Power Supply
Mounting Options
E-MCR-05
12-Slot Media Converter Rack
WMBD
DIN Rail Bracket 5.0” [127 mm]
WMBD-F
DIN Rail Bracket (flat) 3.3” [84 mm]
WMBL
Wall Mount Bracket 4.0” [102 mm]
WMBV
Vertical Wall Mount Bracket 5.0” [127 mm]
RMS19-SA4-01
4-Slot Media Converter Shelf
Features
4
AIS (Alarm Indication Signal)
4
Coax Line Build Out
4
Switch selectable for DS3/T3 or E3
4
Loopback – Coax and Fiber
4
LEDs for immediate visual status
4
Supports dual or single fiber
4
Supports multimode and single mode
fiber at a variety of distances
4
Supports CWDM SFPs
Integrate Voice & Data on Fiber Network
Ordering Information
SCSCF3011-110
(2) Coax (BNC)
to 1300nm multimode (ST)
[2 km/ 1.2 mi.] Link Budget: 14.0 dB
SCSCF3013-110
(2) Coax (BNC)
to 1300nm multimode (SC)
[2 km/ 1.2 mi.] Link Budget: 14.0 dB
SCSCF3014-110
(2) Coax (BNC)
to 1310nm single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SCSCF3015-110
(2) Coax (BNC)
to 1310nm single mode (SC)
[40 km/24.9 mi.] Link Budget: 29.0 dB
SCSCF3016-110
(2) Coax (BNC)
to 1310nm single mode (SC)
[60 km/37.3 mi.] Link Budget: 32.0 dB
SCSCF3017-110
(2) Coax (BNC)
to 1550nm single mode (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
SCSCF3040-110
(2) Coax (BNC)
to SFP slot (empty)
Single Fiber Products
Recommended use in pairs
SCSCF3029-110
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SCSCF3029-111
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SCSCF3029-112
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
SCSCF3029-113
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
SCSCF3029-114
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
SCSCF3029-115
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
SCSCF3029-116
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[80 km/49.7 mi.] Link Budget: 33.0 dB
SCSCF3029-117
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[80 km/49.7 mi.] Link Budget: 32.0 dB
*The SCSCF30xx-110 will only work with
another CCSCF30xx-110 or SCSCF30xx-110.
The product does not work with a -10x model.
DS3-T3/E3 and STS-1 Coax to Fiber