MEAN WELL CEN-100-48 Manual Do Utilizador

20V

24V

30V

36V

54V

48V

42V

0 ~ 4.8A

0 ~ 4A

0 ~ 3.2A

0 ~ 2.65A

0 ~ 1.77A

0 ~ 2A

0 ~ 2.28A

96W

96W

96W

95.4W

95.58W

96W

95.76W

2.0Vp-p

2.7Vp-p

3Vp-p

3.6Vp-p

5Vp-p

4.6Vp-p

4Vp-p

¡Ó10%
¡Ó3.0%
¡Ó5.0%
3000ms / 230VAC 5000ms / 115VAC at full load

90 ~ 295VAC

127 ~ 417VDC

47 ~ 63Hz

PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

88%

89%

90%

90%

91%

91%

90%

22.8 ~ 26V

28 ~ 32V

34 ~ 38V

41 ~ 46V

59 ~ 65V

54 ~ 60V

47 ~ 52V

1.4A/115VAC

0.7A/230VAC

0.5A/277VAC

<0.75mA / 240VAC

95 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Hiccup mode, recovers automatically after fault condition is removed

-30 ~ +70

¢J (Refer to "Derating Curve")

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

¢J

¡Ó

¢J

¢J

0.03%/

(0 ~ 50

)

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

519.5K hrs min.

MIL-HDBK-217F (25

)

¢J

195*62.5*40.5mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Constant current operation region is within 65% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

¢J

0.6Kg; 24pcs/15.4Kg/1.11CUFT

Protection type : Shut down o/p voltage, re-power on to recover

100

10

(RTH1)

¢J¡Ó ¢J

Protection type : Shut down o/p voltage, re-power on to recover

I/P-O/P:3.75KVAC

I/P-FG:2KVAC

O/P-FG:0.5KVAC

UL8750, CSA C22.2 No. 250.0-08(except for 48V, 54V), TUV EN61347-1, EN61347-2-13, IP66, J61347-1, J61347-2-13 approved

I/P-O/P, I/P-FG, O/P-FG: >100M Ohms / 500VDC / 25

/ 70% RH

¢J

Compliance to EN55015, EN61000-3-2 Class C (

65% load) ; EN61000-3-3

¡Ù

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV), criteria B

13 ~ 20V

15.6 ~ 24V

19.5 ~ 30V

23.4 ~ 36V

35.1 ~ 54V

31.2 ~ 48V

27.3 ~ 42V

4.8A

4A

3.2A

2.65A

1.77A

2A

2.28A

17 ~ 22V

22 ~ 27V

27 ~ 33V

33 ~ 40V

49 ~ 58V

43 ~ 53V

37 ~ 46V

3.12 ~ 4.8A

2.6 ~ 4A

2.08 ~ 3.2A

1.72 ~ 2.65A

1.15 ~ 1.77A

1.3 ~ 2A

1.48 ~ 2.28A

..

½

Features :

100W Single Output LED Power Supply

¡E

¡E

¡E

¡E

¡E
¡E

¡E

¡E

¡E

¡E

¡E

¡E

Universal AC input / Full range (up to 295VAC)
Protections: Short circuit / Over current / Over voltage / Over temperature
Output voltage and constant current level adjustable
Built-in active PFC function
IP66 design for indoor or outdoor installations

Cooling by free air convection
100% full load burn-in test
High reliability
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
Suitable for dry / damp / wet locations
3 years warranty

¡E

Class 2 power unit

¡½

Features :

( except for 48V,54V )

( for 48V,54V only)

COLD START 45A(t

=85 s measured at 50% I

) at 230VAC

width

peak

£g