Philips Multigroom 7100 QG3384/42 Folheto

Use the narrow mini shaver to shave along con-

toured edges to remove any stubble while creating 

a smooth, well-defined beard line.

w

 Before using the mini shaver, always check it 

for wear and damage. If the mini shaver shows 

signs of wear or damage, do not use it as injury 

may occur. Do not use the mini shaver until it 

has been replaced. 

Pre-trim the contours desired with the  

    trimmer or precision trimmer without a  

    comb attachment.  

Put the mini shaver on the Groomer handle. 

Gently press the mini shaver onto the skin  

    and shave along contoured edges to remove  

    any stubble. Do not press too hard (fig. 22). 

Be certain the Groomer is in the OFF  

   position.  

  Remove the trimmer by turning counter-

clockwise and pulling it off the Groomer 

handle.  

  Put the nose/ear hair trimmer on the 

Groomer handle (1) and turn clockwise (2) 

(fig. 23).

 

w

 Make sure nasal passages are clean. 

Put the nose/ear hair trimmer on the 

 

    Groomer handle (1) and turn clockwise (2)  

    (fig. 23).  

Turn the Groomer ON and insert the tip   

    of the attachment into one nostril (fig. 24). 

Slowly move the tip in and out while  

turning it around at the same time in order 

to remove unwanted hair. For best results, 

make sure the side of the tip is firm against 

skin. This will reduce the tickling effect that 

can occur during trimming of nose hair. 

 Turn off Groomer.  Rinse attachment clean 

after each use.

w

 Clean outer area of ear and ear canal.  Make  

  sure it is free of wax.

w

 Nose/ear hair trimmer should be on the  

 Groomer. 

Turn the Groomer ON and move the tip 

softly around the edge of ear to remove hairs 

extending beyond the outer ear (fig. 25).  

Carefully insert the tip into outer ear canal 

    (fig. 26).

 Turn off Groomer.  Rinse attachment clean 

after each use. 

 

w

 Clean the attachments after each use.

w

  Always switch Groomer OFF, unplug 

and remove power supply cord from 

Groomer before cleaning.

w

 Do not use compressed air, abrasive cleaning  

  agents, scourers or liquids such as alcohol,  

  benzene, bleach or acetone to clean the  

 

 Groomer and attachments.

w

  Never clean, replace or remove Groomer 

attachments with motor ON.

w

  Do not apply pressure to cutters.

w

 Do not touch cutters with hard objects as this  

  may damage them.

w

  If cut hairs have accumulated in the comb 

area, remove hairs by shaking, blowing or using 

cleaning brush provided. Remember to adjust 

the trimming length back to your selected set-

ting when you replace the comb on Groomer.

Make sure the Groomer is switched OFF   

  and disconnected from the electrical outlet. 

Remove any comb or attachment. 

Blow and/or shake out any hair that may  

    have accumulated in the comb or attachment. 

To contour the hairline around the ears,  

    comb the hair ends over the ears. 

Tilt the Groomer in such a way that only  

    one edge of the cutter blades touches the  

    hair ends when you shape the contours    

    around the ears (fig. 16). 

Be careful not to trim too much. The hairline 

should be close to the ear. 

To contour the nape of the neck or  

 

  sideburns, turn the Groomer and make    

  downward strokes (fig. 17). 

Move the Groomer slowly and smoothly  

    following the natural hairline. 

Put the trimmer on Groomer handle (1) and 

turn clockwise (2) (fig. 2). 

Slide the beard & moustache comb into  

    the guiding grooves on both sides of the    

    handle (fig. 18). 

Press the Hair Length Setting Selector (1) 

and slide the comb to the desired setting (2) 

(fig. 19). 

The beard and moustache comb cuts hair to a 

length of 3/64-23/32in / 1-18mm. 

w

  If you are trimming for the first time, start 

by using the comb at the maximum trimming 

length setting (23/32 in/18mm) to prevent  

accidentally trimming hairs too short.  As you 

become familiar with the settings, adjust Hair 

Length Setting Selector to desired trimming 

length. Selector will “click” into position at each 

setting.

Turn the Groomer ON (fig. 5). 

 To trim in the most effective way, move 

the Groomer against the direction of hair 

growth. Make sure the surface of the comb 

always stays in contact with the skin.

NOTE: Since all hairs do not grow in the same 

direction, you may want to try different trimming 

positions (i.e., upwards, downwards, or across). 

Practice is best for optimum results.

w

If a lot of hair has accumulated in the comb,  

  remove the comb and blow and/or shake the  

  hair out of the comb. You can also use the    

  cleaning brush provided to remove  

 

  hair from the comb area.

w

  REMEMBER: You must reset the hair length 

selector back to your desired setting every time 

you replace the comb on the appliance. 

w

The remaining hair length corresponds with   

  the smallest distance between the cutting    

 blade and the spot where the comb is in contact  

  with the skin.

Remove comb if you are: 

w

  Defining hair lines

w

  Trimming nape of neck

w

  Removing single, unwanted hairs 

Be certain the Groomer is in the OFF    

   position. 

Remove the comb by pressing the Hair  

    Length Setting Selector (1) and slide the  

    comb upwards (2). Pull comb off Groomer . 

 Turn the Groomer ON (fig. 5). 

Make well-controlled movements. Touch the  

  hair/skin lightly with the Groomer. 

w

 Use the precision trimmer to cut shapes in 

beard hair or scalp hair. 

w

 Be careful when using the precision trimmer as 

it removes every hair it touches. 

Put the precision trimmer on the Groomer 

    handle (1) and turn clockwise (2) (fig. 20).  

Make careful and controlled movements with  

    the precision trimmer. 

For best results, move the precision trimmer  

    against the direction of hair growth making  

    sure it is in full contact with the skin (fig. 21). 

w

 Make sure the shaving foil is in complete  

  contact with your skin for the closest shave  

  and minimum foil wear.

w

 Pressing too hard may cause skin irritation.

w

 Practice is best for optimum results.

Put the Bodygroom Shaver on the Groomer  

    handle (1) and turn clockwise (2) (fig. 7). 

Turn the Groomer ON (fig. 5).

Stretch your skin taut with your free hand  

and gently press Groomer to skin and move  

it slowly and smoothly, making sure the  

shaving foil is in full contact with the skin  

(fig. 8). Do not press too hard.  Too much 

pressure can distort the foil and cause skin 

irritation.  

Always move the Groomer against the  

    direction of hair growth (fig. 9). 

Turn OFF Groomer (fig. 5). Clean the  

    body shaver after each use.

w

Make sure that the appliance is fully charged  

  before you start clipping hair.  

w

 Before you start clipping, make sure that the  

  head of the person whose hair you are cutting  

  is at the same level as your chest so that all   

  parts of his/her head are clearly visible and    

  within easy reach.

w

 Make sure the hair is clean and dry.

w

 Before you begin, comb the hair in the direction  

  of growth (fig. 10).

w

   To achieve optimal clipping results, always move 

the appliance slowly through the hair against 

the direction of hair growth.  

Put the trimmer on Groomer handle (1) and 

turn clockwise (2) (fig. 2). 

Slide the hair clipping comb into the guiding  

    grooves on both sides of Groomer handle  

    (fig. 11).

 Press the Hair Length Setting Selector (1) 

and slide the comb to the desired setting (2) 

(fig. 12).

The hair clipping comb cuts hair to a length of 1/8 

in - 25/32 in / 3-20mm.

The setting selected is shown on the back  

    of the Groomer. 

When you are clipping for the first time, start 

at the maximum clipping length setting (25/32 

in/20mm) to familiarize yourself with the appliance 

and prevent accidentally trimming hairs too 

short. As you become familiar with the settings, 

adjust the Hair Length Setting Selector to desired 

trimming length. Selector will ‘click’ into position at 

each setting. 

Turn the Groomer ON (fig. 5). 

Make sure that the flat part of the comb is  

    always in full contact with the scalp to obtain 

    an even result (fig. 13). 

Move the appliance slowly over the crown  

    from different directions to achieve an even  

    result (fig. 14). 

   Always move the appliance against the    

  direction of hair growth. 

 Make overlapping passes over the head to 

ensure that all hair that should be cut has 

been cut. 

Turn the Groomer off and remove the hair 

    clipping comb often to blow and/or shake  

    out hair that has accumulated. 

w

 REMEMBER: You must reset the hair length    

  selector back to your desired setting every   

  time you replace the hair clipping comb on the  

 appliance.  

 

w

Use the Groomer without a comb to clip hair  

  very close to the skin (3/64in./1mm) or to  

  contour the neckline and area around the ears.  

Remove the hair comb by pressing the Hair  

    Length Setting Selector (1) and slide the  

    comb upwards (2). Pull comb off Groomer  

    (fig. 15).

Be careful when you are clipping without a comb 

attachment as when the Clipper is turned on it 

will remove every hair it touches. 

 

 

When using an electric appliance, basic safety 

precautions should always be followed, including 

the following: 
Read all instructions before using this 

To reduce the risk of electric shock: 
1.   Do not reach for a corded groomer that has 

fallen into water. Unplug immediately.

2.   Power plug and the accessories connected 

to it are not for immersion or for use in 

shower. 

3.  Do not use an extension cord with this 

 appliance.

4.   Always unplug the groomer from the  

electrical outlet immediately after use, except 

when groomer is (re)charging.

5.   Unplug and remove power supply cord from 

groomer before cleaning. 

6.   The batteries used in this device may present 

a fire or chemical burn hazard if mistreated. 

Do not disassemble, heat above 100°C 

(212°F) or incinerate. 

shock or injury to persons: 
1.   Close supervision is necessary when  

this appliance is used by, on, or near children 

or invalids.

2.   Use this groomer for its intended household 

use as described in this manual. Do not use 

attachments not recommended by Philips 

Electronics North America Corporation. 

3.   Never operate this groomer if it has a  

damaged cord or plug, if it is not working  

properly, if it has been dropped, damaged, 

or dropped into water while plugged in. For 

assistance call 1-800-243-3050. 

4.   Keep the groomer, cord, charging plug and 

any attachments away from heated  

surfaces.

5.   Never drop or insert any object into any 

opening.

6.   Do not operate, charge, clean or plug in 

groomer outdoors or where aerosol (spray) 

products are being used or where oxygen is 

being administered.

7.   Always check foils, cutters, cutting unit, 

combs and trimmers before using the groom-

er. Do not use the groomer if foils, cutters, 

cutting unit, combs or trimmers are damaged, 

as injury may occur.

8.   Always attach plug to groomer first, then  

to outlet. To disconnect, turn groomer “OFF”, 

then remove plug from outlet.

9.   To prevent possible damage to the cord, do 

not wrap cord around the groomer.

10.  Never put groomer in direct sunlight or 

store at a temperature above 140°F.

11.  This groomer is for use on human hair only. 

Do not use this groomer for any other  

purpose.

12. Groomer is water-safe and can be rinsed  

  under running tap water or used in the  

  shower. Do not submerge groomer in water. 

13. Only use the power plug and other  

  accessories supplied with the appliance.

w

 Simply press the Turbo Button for a turbo 

power boost for fast results and the Turbo 

indicator will light up blue. The memory  

function will remember the last used setting. 

 

w

 Use this Groomer for its intended household  

  use as described in this manual.

w

  Before using, check foil, cutters and trimmers 

for wear or damage. If foil, cutters or trim-

mers show signs of wear or damage, do not 

use Groomer as injury may occur. Do not use 

Groomer until foil, cutters or trimmers have 

been replaced. 

w

 Make sure that the Groomer is fully charged  

  before you start trimming.  

w

Make sure hair is clean and dry as wet hair 

tends to stick to the body.

Take your time and do not move the Groomer 

too fast. Make smooth and gentle movements. 

Charge according to directions. Unplug 

groomer from outlet and remove cord.  

Press ON/OFF button ON to begin trimming. 

If the charge runs low, the battery status 

indicator will light up orange. 

Connect appliance plug to Groomer. A quick 

charge for 5 minutes gives you 5 minutes of 

trimming time. 

w

 Always use the body trimming comb when    

  trimming sensitive areas.

Put the trimmer on the Groomer handle  

    (1) and turn clockwise (2) (fig. 2). 

Slide the body trimming comb into the  

    guiding grooves on both sides of the handle  

    (fig. 3).  

Press the Hair Length Setting Selector (1) 

and slide the comb to the desired setting (2) 

(fig. 4). 

The body trimming comb cuts hair to a length of 

1/8 - 15/32in / 3-12mm.

The setting selected is shown on the back  

    of the Groomer. 

w

  If you are trimming for the first time, start 

by using the comb at the maximum trimming 

length setting (15/32 in/12mm) to prevent 

accidentally trimming hairs too short.  As you 

become familiar with the settings, adjust Hair 

Length Setting Selector to desired trimming 

length.  Selector will ‘click’ into position at each 

setting.

Turn the Groomer ON (fig. 5). 

To trim in the most effective way, move the  

    Groomer slowly against the direction of hair  

    growth (fig. 6).  Make sure the surface of the  

    comb always stays in contact with the skin. 

NOTE:  Since all hairs do not grow in the same 

direction, you may want to try different trimming 

positions (i.e., upwards, downwards, or across).  

Practice is best for optimum results.

w

 If a lot of hair has accumulated in the comb,   

  remove the comb and blow and/or shake the  

  hair out of the comb.  You can also use the    

  cleaning brush provided to remove hair from  

  the comb area.

w

 REMEMBER: You must reset the hair length  

  setting selector back to your desired setting  

  every time you replace the comb on the  

 appliance.

w

 The length setting is equal to the hair length  

  that will remain after trimming.  

Turn off Groomer (fig. 5).  Rinse the comb  

    clean after each use. 

w

 Do not use this Groomer to shave facial or  

  scalp hair.  The Groomer should only be used  

  on skin below the neckline. 

w

 When shaving sensitive areas, you may feel  

  some discomfort, irritation or reddening of the  

  skin.  This is normal as your skin needs time to  

  adjust to shaving.

w

 If your hair is longer than 13/32 in/10 mm,  

  trim hair with the body trimming comb first  

  for optimum shaving results.

w

 For dry use, be certain your skin is clean and  

  dry before using the Groomer.

w

 For wet use, you may prepare your skin with  

  lathered soap or shaving foam before using the  

 Groomer.

w

 Do not use the shaver if foil or cutters are  

  damaged or broken as injury may occur.   

Rinse combs, attachments and appliance  

    under warm tap water or with the supplied  

    cleaning brush. 

  Shake excess water from combs and  

    attachments and allow to air dry thoroughly.

  Place the attachment back on the Groomer 

    handle.

  Cleaning the Mini Foil Shaver

Separate the top part of the mini shaver  

    from its body (fig. 27). 

Blow and/or shake out any hair that may  

    have accumulated inside the mini shaver  

    (fig. 28). 

Clean the top part of the mini shaver under  

    warm tap water (fig. 29). 

w

  The shaving foil is very delicate and should not 

be handled.

w

  If foil becomes damaged, do not continue using 

the mini shaver.  Do not apply pressure to shav-

ing foil.

w

  Do not clean the foil with the supplied brush, 

as this may cause damage. 

Shake excess water from mini shaver and  

    allow to air dry thoroughly. 

Do not use a towel to dry the mini shaver as 

damage to the shaving foil could occur. 

  Cleaning the Body Shaver

Pull the shaving unit out of the body shaver  

    (fig. 30). 

Blow and/or shake out any hair that may have 

accumulated inside the body shaver (fig. 31). 

Clean the body shaver and shaving unit  

    under warm tap water (fig 32). 

w

  The shaving foil is very delicate and should not 

be handled.

w

 If foil becomes damaged, do not continue  

  using the body shaver.  Do not apply pressure  

  to shaving foil. 

w

  Do not clean the foil with the supplied brush, 

as this may cause damage. 

Shake excess water from body shaver and  

    shaving unit and allow to air dry thoroughly. 

Do not use a towel to dry the shaving unit as  

damage could occur. 

w

If the shaving unit is worn or damaged, do not  

 continue using the Bodygroom shaver. Replace  

 the shaving unit immediately.

w

 It is recommended that you replace your  

  shaving unit once a year. 

w

  A worn or damaged shaving unit should only  

be replaced with an original Philips Norelco 

shaving foil, model BG2000, which is  

available on the Philips Norelco website,  

www.philips.com/support or call  

 1-800-243-3050 for assistance.

w

 The foil is a precision part.  Handle with care.

 

Always switch Groomer OFF and remove   

    Groomer plug from outlet before  

    replacing shaving unit.

Remove the shaving unit head by pulling it off  

    the appliance. 

Place the new shaving unit head on the    

    Groomer by snapping it into place.   

 

    You will hear a “click”. 

After replacing the shaving unit head, check that 

the shaving head is firmly attached before using 

Groomer.

This Groomer has no other user-serviceable

parts. For assistance call 1-800-243-3050. 

 

w

 Be sure Groomer is turned OFF. Remove cord  

  from outlet and Groomer before storing in a  

  safe, dry location where it will not be crushed,  

  banged, or subject to damage.

w

 Store the Groomer and attachments in the   

  pouch to prevent damage.

w

  Do not wrap cord around Groomer when 

storing.

w

 Store cord in a safe location where it will not  

  be cut or damaged. 

w

 Do not place or store Groomer where it can  

  fall or be pulled into a tub or sink, water or   

  other liquid while plugged in. 

 

 

A  Bodygroom Shaver

B  Mini Foil Shaver

C   Nose/Ear  Hair  Trimmer

D  Precision Trimmer

E  Full Size Metal Guard Trimmer

F Handle

G  On/Off Button

H  Turbo Button

I  Turbo Status Indicator

J  Battery Status Indicator

K  Storage Pouch

L  Small Appliance Plug

M Adapter

N  Cleaning Brush

O  Body Trimming Comb

P  Beard and Moustache Comb

Q  Hair Clipping Comb

  Full 2-Year Warranty

  45-Day Money-Back Guarantee

 

        

         

This symbol indicates that 

         

the Groomer can be used

         

in the bath or shower.

Congratulations on your purchase and welcome 

to Philips Norelco!

To fully benefit from the support that Philips 

Norelco offers, register your product at 

www.norelco.com/register 

 

Like many new products, your Philips Norelco  

Multigroom Pro Grooming Kit

 

may take a little 

getting used to. If you are using an electric 

Groomer for the first time, or if you’ve been 

using a different brand, take the time to acquaint 

yourself with your new Grooming Kit.

 

Your Multigroom Pro Grooming Kit features 

head to toe styling with a Bodygroom shaver 

and powerful battery combined with all the 

attachments to make trimming facial hairs or hair 

clipping goof proof.

 

Throw your scissors away and put your new  

Multigroom Pro Grooming Kit to the test. We 

guarantee precise, professional results or Philips

 

Norelco will refund you the full purchase price as 

long as the request is received within 45 days of 

purchase.  

 

1

/

8

 - 

15

/

32

 in

3-12mm

3

/

64

 - 

23

/

32

 in 

1-18mm

1

/

8

 - 

25

/

32

 in

3-20mm

A

B

C

Q

P

O

N

M

L

D

E

F

G

H

I

K

J

1

2

1

2

2

1

1

2

2

1

1

2

3 - 20

2

3 - 20

1

3 - 20

1

3

2

For assistance visit our website: 

Online information is available 24 hours a day,  

7 days a week.

w

  This Philips Norelco Groomer contains a 

rechargeable Lithium-Ion battery, which must 

be disposed of properly (fig. 33).

w

 Battery may only be removed when  

 

  Groomer is to be discarded.

w

 For assistance, visit our website:  

  www.philips.com/support or  

  call toll free: 1-800-243-3050.

Unplug electrical cord from outlet and    

    Groomer before dismantling Groomer.

Allow the Groomer to run until the  

    battery is completely empty/depleted.  

 

    Turn Groomer off. 

Remove any comb and/or attachment from  

   Groomer.

 

  Check if there are any screws in the back or 

    front of the appliance. If so, remove them.  

 

  Remove the back and/or front panel of the  

    appliance with a screwdriver. If necessary,  

    also remove additional screws and/or parts  

    until you see the printed circuit board with  

    the rechargeable battery.  

 

  If necessary, cut the wires to separate the  

    printed circuit board and the rechargeable  

    battery from the appliance. 

  Do not attempt to replace battery. Insulate  

    battery ends by covering with tape and  

    or  place battery in a small plastic bag.  

 

    Discard Groomer.

  Contact your local town or city officials for  

    battery disposal information or call  

    1-800-8-BATTERY or www.rbrc.com for  

    drop-off locations. 

Multigroom

Pro

w

 Fully charge Groomer before using for the first  

 time or after non-use for a long period of time.

w

 Charging, recharging or using Groomer at  

 temperatures below 40˚F or higher than 95˚F  

  adversely affects  lifespan of the battery.

w

 If the Groomer is subjected to a major change  

  in temperature, pressure or humidity, let the  

  Groomer acclimatize for 30 minutes before  

 using. 

   

1 

Be certain Groomer is OFF.  

Connect small plug to Groomer and plug the 

adapter into any 120V AC outlet (fig. 1). Use 

only the cord provided.

w

 An adaptor plug may be necessary for power 

cord usage in some foreign countries. Use an 

attachment plug adaptor of the proper  

configuration for the power outlet.  

It will take approximately 1 hour to fully 

charge the Groomer for a cordless trimming  

time of up to 60 minutes.   

The Battery Status Indicator will blink white 

to indicate the Groomer is charging. 

If the battery runs low (approximately 10 

minutes of grooming time left) the Battery 

Status Indicator will light up orange indicat-

ing the Groomer needs to be (re) charged.  

Disconnect the cord and unplug from  

    electrical outlet. 

4222 002 8405 1

 

If you are not fully satisfied with your Philips Norelco 

Groomer send the product back and we’ll refund you 

the full purchase price.  

assistance. 
Delivery of refund check will occur 6–8 weeks AFTER 

receipt of returned product.

Philips Electronics North America Corporation warrants each new Philips 

Norelco product, Model QG3384 (except cutters, combs and foils) 

against defects in materials or workmanship for a period of two years 

from the date of purchase, and agrees to repair or replace any defective 

product without charge.

IMPORTANT: This warranty does not cover damage resulting from 

accident, misuse or abuse, lack of reasonable care, the affixing of any 

attachment not provided with the product or loss of parts or subjecting 

the product to any but the specific voltage.* Use of unauthorized 

replacement parts will void this warranty.

In order to obtain warranty service, simply go to www.philips.com/

norelco or call 1-800-243-3050 for assistance. It is suggested that for 

your protection you return shipments of product by insured mail, 

insurance prepaid. Damage occurring during shipment is not covered by 

this warranty. NOTE: No other warranty, written or oral, is authorized 

by Philips Electronics North America Corporation. This warranty gives 

you specific legal rights, and you may also have other rights which vary 

from state to state. Some states do not allow the exclusion or limitation 

of incidental or consequential damages, so the above exclusion and 

limitations may not apply to you.

*Read enclosed instructions carefully.

Manufactured for: 

Philips Consumer Lifestyle

A Division of Philips Electronics North America Corporation 

P.O. Box 10313, Stamford, CT 06904

This symbol on the product’s nameplate means it is

listed by Underwriters’ Laboratories, Inc.

Norelco is a Registered Trademark of Philips Electronics 

North America Corporation.

PHILIPS is a Registered Trademark of Koninklijke Philips N.V.

© 2013 Philips Electronics North America Corporation. All Rights Reserved.

QG3384

Rechargeable Cordless

Electric Groomer

Register your product and get support at

  

www.norelco.com/register