RAM Mount RAM-VB-167-SW1 Folheto
This document, including images, may not be reproduced partly or fully without the expressed written consent of National Products, Inc.
Vehicle base for the
SPECIFICATIONS
Placement
Passenger side on the floor, under front seat
Passenger side on the floor, under front seat
Drilling Required
No - uses existing seat bolts
No - uses existing seat bolts
Seat Configuration
Bucket
Bucket
Construction/Finish
Steel/Black Powdercoat
Steel/Black Powdercoat
Pole or Pedestal
Purchased Separately
Purchased Separately
Weight
4 lbs.
4 lbs.
Dimensions
A = 17.44", B = 9", C = 2.12"
Hole Center = 16.44"
A = 17.44", B = 9", C = 2.12"
Hole Center = 16.44"
Features
Complete Vehicle Mount
RAM-VB-167-SW1
Vehicle Base
RAM-VB-167
Installs in minutes with no drilling required
Minimal intrusion into passenger leg space
Lifetime warranty
Minimal intrusion into passenger leg space
Lifetime warranty
RAM No-Drill
TM
Seat Bases
National Products, Inc.
Item Number
RAM-VB-167 & RAM-VB-167-SW1
RAM-VB-167 & RAM-VB-167-SW1
FORD FUSION (2006-2012)
LINCOLN MKZ (2007-2010)
MERCURY MILAN (2006-2010)
LINCOLN MKZ (2007-2010)
MERCURY MILAN (2006-2010)
National Products, Inc.
Website: www.ram-mount.com
Email: staff@ram-mount.com
Email: staff@ram-mount.com
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
National Products, Inc.
Website: www.ram-mount.com
Email: staff@ram-mount.com
Email: staff@ram-mount.com
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
Vehicle base for the
INSTALLATION INSTRUCTIONS
Depending on the vehicle trim level, there may be plastic covers over the seat frame legs where these meet the floor. If
this is the case in your vehicle, carefully remove the trim and store it so it can be replaced when the base is later
removed.
this is the case in your vehicle, carefully remove the trim and store it so it can be replaced when the base is later
removed.
1. Slide the seat to its rear most position.
2. Remove the two front seat leg bolts using the appropriate wrench. A 13mm socket is common.
3. Place the mounting base over the seat frame legs and align the holes.
4. Pass the factory bolts through the holes in the base and start the thread of the seat bolts by hand.
5. Complete the installation by using the wrench to fully tighten the seat leg bolts.
6. After a week of use, check seat leg bolts and re-tighten if necessary.
2. Remove the two front seat leg bolts using the appropriate wrench. A 13mm socket is common.
3. Place the mounting base over the seat frame legs and align the holes.
4. Pass the factory bolts through the holes in the base and start the thread of the seat bolts by hand.
5. Complete the installation by using the wrench to fully tighten the seat leg bolts.
6. After a week of use, check seat leg bolts and re-tighten if necessary.
This document, including images, may not be reproduced partly or fully without the expressed written consent of National Products, Inc.
RAM No-Drill
TM
Seat Bases
National Products, Inc.
Item Number
RAM-VB-167 & RAM-VB-167-SW1
RAM-VB-167 & RAM-VB-167-SW1
FORD FUSION (2006-2012)
LINCOLN MKZ (2007-2010)
MERCURY MILAN (2006-2010)
LINCOLN MKZ (2007-2010)
MERCURY MILAN (2006-2010)