Sony UNIOPS7T1 Folheto
IR Illuminator
(Images 1)
Pressurized Dome Enclosures
UNI-OPS7C1 & UNI-OPS7T1
Security Camera Enclosures
The Sony UNI-OPS7C1/T1 outdoor 7-inch pressurized
housing offers versatility and camera protection for the
SNC-RZ30N and SNC-RZ50N cameras. Pressurization
eliminates the effects of moisture, dirt, and pollution on
valuable camera equipment. A heater and blower are
standard. 24VAC input.
housing offers versatility and camera protection for the
SNC-RZ30N and SNC-RZ50N cameras. Pressurization
eliminates the effects of moisture, dirt, and pollution on
valuable camera equipment. A heater and blower are
standard. 24VAC input.
•
Designed for use with the SNC-RZ50N and SNC-RZ30N
cameras.
cameras.
•
Pressurization seals out condensation,
dust, insects and pollution.
dust, insects and pollution.
•
Superb corrosion protection; excellent for coastal
areas and other extreme environmental conditions.
areas and other extreme environmental conditions.
•
Pressurized to 7 psi.
•
Schraeder valve, and pressure relief valve.
•
Requires UNI-WMB1 or UNI-WMB3 to wall mount.
•
The outdoor pressurized dome camera housing shall be a Sony model UNI-OPS7C1/T1, designed for the SNC-RZ50N or
SNC-RZ30N cameras. The housing shall be capable of withstanding a total of 7 psi (48 Kpa) of nitrogen gas injected
through a Schraeder valve located on top of the machined stainless steel plate. A pressure relief valve located across
from the Schraeder valve will provide an escape for pressure exceeding 7 psi (48 Kpa). Two (2) o-ring seals shall be
included, 3.5 x 235mm (inner diameter) and 3.5 x 114.3mm (inner diameter). A 10-pin hermetically sealed connector,
located at the top of the pressurized housing shall provide power, video and control functions. The housing shall be
constructed of 3mm durable UV-resistant engineered plastic, with a UL flame rating of 94-5VA. The lower dome shall be
made of an injection molded, 3mm thick, optically clear thermoplastic polycarbonate. The dome shall be held in place
with minimum of (9) fasteners, and a safety cable shall be provided to hold the dome while servicing. Access to the
enclosure shall be from below with (9) captive fasteners used to press the dome against a sealing o-ring. A twist-off feature
shall allow for the final removal of the dome. The housing shall come standard with pendant mount. A wall mount bracket,
Sony model UNI-WMB3 is available (sold separately). The housing shall include a camera mounting bracket that integrates
a heater and blower. The blower shall draw 1.4W continuous power. The 50W heater shall turn on at 60°F (15°C) and turn
off at 80°F (27°C). The housing shall support a temperature range of -50°F to 120°F (-50°C to 50°C). The unit shall have a
weight not to exceed 5 kg (without camera) and dimensions of 14.7 x 11.2 x 11.2 inches (366 x 285 x 285mm). The input
voltage is 24VAC and the housing shall include 24VAC to 12VDC power supply for the camera.
through a Schraeder valve located on top of the machined stainless steel plate. A pressure relief valve located across
from the Schraeder valve will provide an escape for pressure exceeding 7 psi (48 Kpa). Two (2) o-ring seals shall be
included, 3.5 x 235mm (inner diameter) and 3.5 x 114.3mm (inner diameter). A 10-pin hermetically sealed connector,
located at the top of the pressurized housing shall provide power, video and control functions. The housing shall be
constructed of 3mm durable UV-resistant engineered plastic, with a UL flame rating of 94-5VA. The lower dome shall be
made of an injection molded, 3mm thick, optically clear thermoplastic polycarbonate. The dome shall be held in place
with minimum of (9) fasteners, and a safety cable shall be provided to hold the dome while servicing. Access to the
enclosure shall be from below with (9) captive fasteners used to press the dome against a sealing o-ring. A twist-off feature
shall allow for the final removal of the dome. The housing shall come standard with pendant mount. A wall mount bracket,
Sony model UNI-WMB3 is available (sold separately). The housing shall include a camera mounting bracket that integrates
a heater and blower. The blower shall draw 1.4W continuous power. The 50W heater shall turn on at 60°F (15°C) and turn
off at 80°F (27°C). The housing shall support a temperature range of -50°F to 120°F (-50°C to 50°C). The unit shall have a
weight not to exceed 5 kg (without camera) and dimensions of 14.7 x 11.2 x 11.2 inches (366 x 285 x 285mm). The input
voltage is 24VAC and the housing shall include 24VAC to 12VDC power supply for the camera.
•
Note: To achieve the increased depth with the aspheric design for optimal camera lens to capsule orientation, the polycarbonate
capsule is slightly angled around the highest section. This creates a “line’, visible to the naked eye, around the upper most section
of the capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is not typically seen by
the camera except when used with cameras that have above the horizon tilt capability.
of the capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is not typically seen by
the camera except when used with cameras that have above the horizon tilt capability.
KEY FEATURES
BID SPECIFICATIONS
•
Thermostatically controlled 24VAC heater.
•
Durable engineered plastic top, UL94-5VA UV protected.
•
Clear or tinted dome (1 F stop light reduction).
•
Enhanced optical dome.
•
IP67, designed to meet NEMA 4X for water ingress.
•
Pendant mount standard, 1½-inch NPT quick
connect coupling.
connect coupling.
•
Heater and blower standard.