Psiber Data CTK1015 CableTracker Network ID Kit 226005 Ficha De Dados
Códigos do produto
226005
Activate Link Lights to Identify a Connected Hub or Switch Port
©
2003 Psiber Data Systems Inc.
All Rights Reserved. The Psiber Logo,
psiber, and C
ABLE
T
RACKER
are trademarks of
Psiber Data Systems Inc.
Blink the Lights to ID Ports
Tone and probe kits were designed for one primary mission, to
Tone and probe kits were designed for one primary mission, to
identify the termination point of a cable. Unfortunately, these
were designed for telephony, not network maintenance. In the
Networking environment cable terminations typically end in hub
or switch ports. The CableTracker incorporates three link light
activation speeds (blink rates) to easily identify the cable
termination port by simply looking for the corresponding blink
rate on the port light. Three speeds ensure the widest
compatibility available.
Physical
Signal Generator - CT10
Dimensions:
3.0 in. x 2.4 in. x 1.4 in.
7.6 cm x 6.6 cm x 3.6 cm
Probe - CT15
Dimensions:
8.0 in. x 1.4 in x 1.5 in
20.3 cm x 3.6 cm x 3.8 cm
Signal Frequencies - CT10
Lo Tone - 1kHz; Hi Tone - 8kHz
Reception Frequencies - CT15
Broadband 100Hz-10kHz
Power
One 9 volt Battery Each (not supplied)
Environment
Operating Temperature: 0° to 50°C
Storage Temperature: -10° to 55°C
Product design and specifications subject to change without notice.
S p e c i f i c a t i o n s
C
ABLE
T
RACKER
Network ID Kit
Model Number - CTK1015
Includes: CT10 - Signal Generator
CT15 - Probe
CC2 - Carrying Case
Alligator Clip Leads
RJ-45 Patch Cable
Users Guide
C
ABLE
T
RACKER
Signal Generator
Model Number - CT10
Includes: CT10 - Signal Generator
Alligator Clip Leads
RJ-45 Patch Cable
Users Guide
C
ABLE
T
RACKER
Probe
Model Number - CT15
Includes: CT15 - Probe
Users Guide
Accessories: (sold separately)
CC2 - Carrying Case
Alligator Clip Leads (6" red/black)
RJ-45 Patch Cable (8")
Psiber Data Systems Inc
7075-K Mission Gorge Road
San Diego, California 92120 USA
Phone: 619-287-9970
FAX:
619-287-9978
Internet: www.psiber.com
e-mail: info@psiber.com
O r d e r i n g I n f o r m a t i o n
P r o d u c t F e a t u r e s
q
u
Easy Ethernet or Telephony Connection
Most toners on the market offer RJ-11 hard-wired modular
Most toners on the market offer RJ-11 hard-wired modular
connection. That's because they were designed mostly to be used
in the Telecommunication market. This does nothing for the Lan
technician who is faced with ethernet RJ-45 jacks or patch cords.
The CableTracker Network ID Kit was designed to accommodate
both Computer Network cabling and Telephony cabling. The
Signal Generator (CT10) incorporates a female RJ-45 jack and
detachable alligator clips for punch down blocks or unterminated
cables.
Time Saving Features
The CableTracker incorporates several time and money saving
The CableTracker incorporates several time and money saving
features not found on other Tone and Probe kits. The RJ-45 male
connection and the alligator clips are detachable, meaning cord
failure won't obsolete the your tester. Auto Power Down extends
battery life and a built-in low battery circuit warns when battery
replacement is required, saving unexpected down time searching
for a new battery when the tester just goes dead. The
CableTracker Probe (CT15) incorporated volume control, non-
conductive plastic tip and complete compatibility with existing
toners on the market.
0101-1015-0001 4/03 Printed in U.S.A.