Finder 80.82.0.240.0000 - 6A Monofunction Modular Timer DPST-NO 400Vac IP20 80.82.0.240.0000 Ficha De Dados
Códigos do produto
80.82.0.240.0000
80.01
80.11
1 CO (SPDT)
1 CO (SPDT)
16/30
16/30
250/400
250/400
4,000
4,000
750
750
0.55
0.55
16/0.3/0.12
16/0.3/0.12
500 (10/5)
500 (10/5)
AgCdO
AgCdO
12…240
24...240
12…240
24...240
< 1.8 / < 1
< 1.8 / < 1
10.8...265
16.8...265
10.8...265
16.8...265
(0.1…2)s, (1…20)s, (0.1…2)min, (1…20)min, (0.1…2)h, (1…24)h
± 1
± 1
100
100
50
—
± 5
± 5
100·10
3
100·10
3
–10…+50
–10…+50
IP 20
IP 20
Wiring diagram
(without control signal)
•
Multi-voltage
•
Mono-function
•
Multi-voltage
•
Multi-function
AI: On-delay
DI: Interval
SW: Symmetrical flasher (starting pulse on)
BE: Off-delay with control signal
CE: On- and off-delay with control signal
DE: Interval with control signal on
DI: Interval
SW: Symmetrical flasher (starting pulse on)
BE: Off-delay with control signal
CE: On- and off-delay with control signal
DE: Interval with control signal on
AI: On-delay
Wiring diagram
(with control signal)
Wiring diagram
(without control signal)
Contact specification
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
Rated load AC1
VA
Rated load AC15 (230 V AC)
VA
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
A
Minimum switching load
mW (V/mA)
Standard contact material
Supply specification
Nominal voltage (U
N
)
V AC (50/60 Hz)
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
V AC
V DC
Technical data
Specified time range
Repeatability
%
Recovery time
ms
Minimum control impulse
ms
Setting accuracy-full range
%
Electrical life at rated load in AC1
cycles
Ambient temperature range
°C
Protection category
Approvals (according to type)
1
Features
Multi-function and mono-function timer range
80.01 - Multi-function & multi-voltage
80.11 - On-delay, multi-voltage
80.01 - Multi-function & multi-voltage
80.11 - On-delay, multi-voltage
•
17.5 mm wide
•
Six time scales from 0.1s to 24h
•
High input/output isolation
•
35 mm rail (EN 60715) mount
•
“Blade + cross” - both flat blade and cross head
screw drivers can be used to adjust the range
and function selectors, the timing trimmer, and
to disengage the rail mounting clip
screw drivers can be used to adjust the range
and function selectors, the timing trimmer, and
to disengage the rail mounting clip
•
New multi-voltage versions with “PWM clever”
technology
technology
80.01 / 80.11
Screw terminal
Screw terminal
F
OR
UL
RATINGS SEE
:
“General technical information” page V
For outline drawing see page 6
80 Series - Modular timers 16 A
VII-2012, www
.finder
net.com