Sony KDL-40X3500U LCD TV KDL-40X3500U Manual Do Utilizador
Códigos do produto
KDL-40X3500U
7
GB
St
art
-u
-u
p
Gui
d
e
3
Press
F
/
f
/
G
/
g
to select the language
displayed on the menu screens, then press
.
4
Press
F
/
f
to select the country/region in
which you will operate the TV, then press
.
If the country/region which you want to use on the
TV does not appear in the list, select “–” instead
of a country/region.
TV does not appear in the list, select “–” instead
of a country/region.
5
Before you start auto tuning the TV, insert
a pre-recorded tape into the VCR
connected to the TV (page 5) and start play
back.
a pre-recorded tape into the VCR
connected to the TV (page 5) and start play
back.
The video channel will be located and stored on
the TV during auto tuning.
If no VCR is connected to the TV, skip this step.
the TV during auto tuning.
If no VCR is connected to the TV, skip this step.
6
Press
G
/
g
to select “OK”, then press
.
7
Press
F
/
f
to select “Antenna” or “Cable”,
then press
.
If you select “Cable”, the screen for selecting the
scan type appears. See “To tune the TV for digital
cable connection” on page 7.
scan type appears. See “To tune the TV for digital
cable connection” on page 7.
The TV starts searching for all available digital
channels, followed by all available analogue
channels. This may take some time, so do not
press any buttons on the TV or remote while
proceeding.
If a message appears for you to confirm the aerial
connection
No digital or analogue channels were found.
Check all the aerial connections and press
channels, followed by all available analogue
channels. This may take some time, so do not
press any buttons on the TV or remote while
proceeding.
If a message appears for you to confirm the aerial
connection
No digital or analogue channels were found.
Check all the aerial connections and press
to
start auto tuning again.
8
When the Programme Sorting menu
appears on the screen, follow the steps of
“Programme Sorting” on page 40.
appears on the screen, follow the steps of
“Programme Sorting” on page 40.
If you do not wish to change the order in which the
analogue channels are stored on the TV, go to next
step.
analogue channels are stored on the TV, go to next
step.
9
Press MENU to exit.
The TV has now tuned in all the available
channels.
channels.
~
When a digital broadcast channel cannot be received, or
when selecting a country/region in which there are no digital
broadcasts in step 4 (page 7), the time must be set after
performing step 9.
when selecting a country/region in which there are no digital
broadcasts in step 4 (page 7), the time must be set after
performing step 9.
To tune the TV for digital cable connection
1
Press
F
/
f
to select “Scan Type”, then
press .
2
Press
F
/
f
to select “Quick Scan” or “Full
Scan”, then press
.
“Quick Scan”: Channels are tuned according to
the cable provider’s information within the
broadcast signal. The recommended setting for
“Frequency”, “Network ID” and “Symbol Rate” is
“Auto” unless your cable provider has supplied
actual values to use. “Quick Scan” is
recommended for fast tuning when this is
supported by your cable provider.
“Full Scan”: All available channels are tuned and
stored. This procedure may take some time. This
option is recommended when “Quick Scan” is not
supported by your cable provider.
For further information about supported cable
providers, refer to the support web site:
http://support.sony-europe.com/TV/DVBC/
the cable provider’s information within the
broadcast signal. The recommended setting for
“Frequency”, “Network ID” and “Symbol Rate” is
“Auto” unless your cable provider has supplied
actual values to use. “Quick Scan” is
recommended for fast tuning when this is
supported by your cable provider.
“Full Scan”: All available channels are tuned and
stored. This procedure may take some time. This
option is recommended when “Quick Scan” is not
supported by your cable provider.
For further information about supported cable
providers, refer to the support web site:
http://support.sony-europe.com/TV/DVBC/
3
Press
G
/
g
/
f
to select “Start”, then press
.
The TV starts searching for channels. Do not press
any buttons on the TV or remote.
any buttons on the TV or remote.
~
Some cable providers do not support “Quick Scan”. If no
channels are detected using “Quick Scan”, perform “Full
Scan”.
channels are detected using “Quick Scan”, perform “Full
Scan”.
Auto tuning the TV