Remington BHT6250 43159560110 Manual Do Utilizador

GB

D

NL

F

E

I

DK

S

FIN

P

SK

CZ

HUN

PL

RU

TR

RO

GR

SL

HR/ SRB

AE

4

5

•  Attach a guide comb to the trimmer head.
•  Turn the unit on.
•  Place the flat top of the trimmer comb against the skin.
•  Slowly slide the trimmer through the hair, in the direction of hair growth.
•  If hair builds up in the trimmer comb during the trimming process, switch the unit off, pull off

the adjustable trimmer comb. Brush trimmer/rinse comb.

•  For a closer and precise shaping, remove the adjustable trimmer comb and trim the hairs

along the outer edge.

•  Remove the Trimmer Comb Attachment.
•  Hold the Trimmer at a right angle to your skin and press down gently.
•  Edge and shape the area as desired.

•  Hold the shaving head to your skin.
•  Stretch your skin with your free hand so hairs stand upright.
•  Only apply light pressure on the shaving head while shaving.
•  Shave against hair growth.

•  Always ensure the trimmer is switched off before changing the attachments.

NOTE: The trimmer comb and shaver attachment can only be attached in one way. If it does not go on
correctly, turn it around and try again.

Care for your product to ensure a long lasting performance. We recommend you clean your appliance
after each use. The easiest and the most hygienic way to clean the appliance is by rinsing the product
head after use with warm water. Always keep the trimmer in the “off” position when not in use.

•  Turn Trimmer off.
•  Remove the adjustable trimmer comb and cutter assembly or shaver attachment.
•  Gently tap on a flat surface to remove hair particles, and brush the remaining hairs away/rinse

under warm water.

•  Rinse the accumulated hair from the cutters and shake of excess water, alternatively, use a

small soft brush.

•  Cleaning should only be done with a soft brush.
•  Only use light-grade oil or sewing machine oil on the blades.
•  Do not use harsh or corrosive cleaners on the units or their cutters.

•  Do not apply pressure or hard objects to cutters.
•  Do not disassemble cutter assembly.

 This trimmer is a wet trimmer, the hand-held part of which may be used in a bath  
  or shower.

•  Always store this appliance and cord in a moisture-free area. Do not store it in

temperatures exceeding 140°F (60°C).

•  Do not wrap the cord of the charging adaptor around the appliance.

WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR INJURY TO PERSONS:
•  An appliance should never be left unattended when plugged in to a power outlet,

except when charging.

•  Keep the power plug and cord away from heated surfaces.
•  Make sure the power plug and cord do not get wet.
•  Do not plug or unplug the appliance with wet hands.
•  Do not use the product with a damaged cord. A replacement can be obtained via our

International Service Centres.

 Do not twist or kink the cable, and don’t wrap it around the appliance.
•  Store the product at a temperature between 15°C and 35°C.
•  Only use the parts supplied with the appliance.
•  The appliance, including its cord, must not be used, played with, cleaned or maintained

by persons under eight years old and should at all times be kept out of their reach.

Use, cleaning or maintenance of the appliance by children over eight or by anyone with

a lack of knowledge, experience or with reduced physical, sensory or mental

capabilities should only be undertaken after receiving appropriate instruction and

under the adequate supervision of a responsible adult to ensure that they do so safely

and that the hazards involved are understood and avoided.

To avoid environmental and health problems due to hazardoussubstances in electrical
and electronic goods, appliances marked with this symbol must not be disposed of with
unsorted municipal waste, but recovered, reused or recycled.

•  The battery must be removed from the appliance before it is scraped.
•  The appliance must be disconnected from the supply mains when removing the battery.
•  Remove attachment head.
•  Using a small flat screwdriver, pry off (2) spring from the top side.
•  Move/push (2) release button to center.
•  Push/pry the inner housing from the out-housing and expose the PCB and battery.
•  Pry the PCB assembly out of the inner housing.