Texas Instruments Evaluation Module for BQ24630 Multi Cell Synchronous Switch-Mode Charger BQ24630EVM BQ24630EVM Ficha De Dados
Códigos do produto
BQ24630EVM
Test Summary
www.ti.com
2.4
Procedure
2.4.1
AC Adapter Detection Threshold
1. Make sure EQUIPMENT SETUP steps are followed. Turn on PS#2.
2. Turn on PS#1
2. Turn on PS#1
Measure
→
V(J5(SYS)) = 0 ± 500mV
Measure
→
V(TP(VREF)) = 0V ± 1000mV
Measure
→
V(TP(REGN)) = 0V ± 500mV
3. Increase the output voltage on PS#1 until D5 (PG) on but do not exceed 5V. Set the power supply #2
to 1.8V ± 100mVDC
Measure
Measure
→
V(J1(VIN)) = 4.5V ± 0.5V
Measure
→
V(J5(SYS)) = 4.5V ± 0.5V
Measure
→
V(TP(VREF)) = 3.3V ± 200mV
Measure
→
V(TP(REGN)) = 0V ± 500mV
Measure
→
D4 (/ACDRV) on, D5 (PG) on
2.4.2
Charger Regulation Voltage
1. Increase the voltage of PS#1 until V(J1(VIN)) = 24V ± 0.1V.
Measure
→
V(J5(BAT, GND)) = 0V ± 1V
2. Put JP5 on (Enable the charging).
Observe
→
D3 (CE) on.
Measure
→
Peak V(J5(BAT)) = 21.0V ± 1V (bq2461x)
Measure
→
Peak V(J5(BAT)) = 18.0V ± 1V (bq2463x)
Measure
→
V(TP(REGN)) = 6V ± 500mV
2.4.3
Charge Current and AC Current Regultion (DPM)
1. Take off JP5 (Disable the charging).
2. Connect the Load #2 in series with a current meter (multimeter) to J5 (BAT, GND). Make sure a
2. Connect the Load #2 in series with a current meter (multimeter) to J5 (BAT, GND). Make sure a
voltage meter is connected across J5 (BAT, GND). Turn on the Load #2. Set the output voltage to 12V
(bq2461x) or 2V (bq2463x).
(bq2461x) or 2V (bq2463x).
3. Connect the output of the Load #1 in series with a current meter (multimeter) to J5 (SYS, GND). Make
sure a voltage meter is connected across J5 (SYS, GND). Turn on the power of the Load #1. Set the
load current to 3.0A ± 50mA but disable the load #1. The setup is now like
load current to 3.0A ± 50mA but disable the load #1. The setup is now like
for HPA422. Make
sure Ibat = 0A ± 10mA and Isys = 0A ± 10mA.
4. Put JP5 on (Enable the charging).
Observe
→
D3 (CE) on
Measure
→
Ibat = 300mA ± 200mA (bq2461x)
Measure
→
Ibat = 125mA ± 60mA (bq2463x)
Observe
→
D7 (STAT1) on; D8 (STAT2) off.
5. Set the Load #2 output voltage to 16.5V.
Measure
→
Ibat = 3000mA ± 300mA
Observe
→
D7 (STAT1) on; D8 (STAT2) off.
6. Enable the output of the Load #1
Measure
→
Isys = 3000mA ± 200mA, Ibat = 1400mA ± 500mA, Iin = 4000mA ± 500mA
7. Turn off the Load #1.
Measure
→
Isys = 0 ± 100mA, Ibat = 3000mA ± 300mA.
8. Increase the Load #2 output voltage from 16.5V to 22V (61x) or 19V (63x).
Measure
→
Isys = 0 ± 100mA, Ibat = 0mA ± 100mA.
Observe
→
D7 (STAT1) off; D8 (STAT2) on.
9. Decrease the Load #2 output voltage back to 16.5V.
Observe
→
D7 (STAT1) on; D8 (STAT2) off.
6
bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger
SLUU396A – January 2010 – Revised July 2010
Copyright © 2010, Texas Instruments Incorporated