Texas Instruments TPS43061 Evaluation Module TPS43061EVM-198 TPS43061EVM-198 Ficha De Dados
Códigos do produto
TPS43061EVM-198
Introduction
1
Introduction
This user's guide contains background information for the TPS43061 as well as support documentation for
the TPS43061EVM-198 evaluation module (PWR198). Also included are the performance specifications,
schematic, and the bill of materials for the EVM.
the TPS43061EVM-198 evaluation module (PWR198). Also included are the performance specifications,
schematic, and the bill of materials for the EVM.
1.1
Background
The TPS43061 is a DC-DC synchronous boost controller designed for a maximum output voltage of 60 V
from an input voltage source of 4.5 V to 38 V. It has a 5.5-V gate-drive supply optimized for use with low
Qg NexFETs. Rated input voltage and output current range for the evaluation module are given in
from an input voltage source of 4.5 V to 38 V. It has a 5.5-V gate-drive supply optimized for use with low
Qg NexFETs. Rated input voltage and output current range for the evaluation module are given in
This evaluation module is designed to demonstrate the small, printed-circuit-board areas that are possible
when designing with the TPS43061 controller. The switching frequency is externally set at a nominal 750
kHz. The gate-drive circuitry for the external high-side and low-side FET is incorporated inside the
TPS43061 package. The PWR198 uses the CSD86330Q3D NexFET power block integrating both the
high-side and low-side FETs. External inductor DCR or resistor current sensing allows for an adjustable
cycle-by-cycle current limit. The compensation components are external to the integrated circuit (IC), and
an external resistor divider allows for an adjustable output voltage. Additionally, the TPS43061 provides an
adjustable undervoltage lockout with hysteresis through an external resistor divider, adjustable slow-start
time with an external capacitor and a power good output voltage indicator. The absolute maximum input
voltage for the PWR198 based on the selected external components is 25 V.
when designing with the TPS43061 controller. The switching frequency is externally set at a nominal 750
kHz. The gate-drive circuitry for the external high-side and low-side FET is incorporated inside the
TPS43061 package. The PWR198 uses the CSD86330Q3D NexFET power block integrating both the
high-side and low-side FETs. External inductor DCR or resistor current sensing allows for an adjustable
cycle-by-cycle current limit. The compensation components are external to the integrated circuit (IC), and
an external resistor divider allows for an adjustable output voltage. Additionally, the TPS43061 provides an
adjustable undervoltage lockout with hysteresis through an external resistor divider, adjustable slow-start
time with an external capacitor and a power good output voltage indicator. The absolute maximum input
voltage for the PWR198 based on the selected external components is 25 V.
Table 1. Input Voltage and Output Current Summary
EVM
Input Voltage Range
Output Current Range
TPS43061EVM-198
V
IN
= 6 V to 12.6 V
I
OUT
= 0 A to 2 A
1.2
Performance Specification Summary
A summary of the EVM performance specifications is provided in
. Specifications are given for an
input voltage of V
IN
= 9 V and an output voltage of 15 V, unless otherwise specified. This EVM is designed
and tested for V
IN
= 6 V to 12.6 V. The ambient temperature is 25°C for all measurements, unless
otherwise noted.
Table 2. TPS43061EVM-198 Performance Specification Summary
Specification
Test Conditions
MIN
TYP
MAX
Unit
V
IN
voltage range
6
9
12.6
V
Output voltage set point
15
V
Output current range
V
IN
= 6 V to 12.6 V
0
2
A
Line regulation
I
OUT
= 2 A, V
IN
= 6 V to 12.6 V
±0.1%
Load regulation
V
IN
= 9 V, I
OUT
= 0.001 A to 2 A
±0.1%
Load transient response
I
OUT
= 0.5 A to 1.5 A
Voltage change
–300
mV
Recovery time
400
µs
I
OUT
= 1.5 A to 0.5 A
Voltage change
210
mV
Recovery time
400
µs
Loop bandwidth
V
IN
= 9 V, I
OUT
= 2 A
19
kHz
Phase margin
V
IN
= 9 V, I
OUT
= 2 A
68
°
Input voltage ripple
I
OUT
= 2 A
10
mVpp
Output voltage ripple
I
OUT
= 2 A
70
mVpp
Output rise time
25
ms
Operating frequency
750
kHz
3
SLVU799A – November 2012 – Revised March 2013
Using the TPS43061 Boost Evaluation Module (EVM)
Copyright © 2012–2013, Texas Instruments Incorporated