Microchip Technology MCP1630DM-DDBS1 Ficha De Dados
©
2007 Microchip Technology Inc.
DS41211D-page 121
PIC12F683
15.5
DC Characteristics:
PIC12F683-I (Industrial)
PIC12F683-E (Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Operating temperature
-40°C
≤
T
A
≤
+85°C for industrial
-40°C
≤
T
A
≤
+125°C for extended
Param
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
V
IL
Input Low Voltage
I/O Port:
D030
with TTL buffer
Vss
—
0.8
V
4.5V
≤
V
DD
≤
5.5V
D030A
Vss
—
0.15 V
DD
V
2.0V
≤
V
DD
≤
4.5V
D031
with Schmitt Trigger buffer
Vss
—
0.2 V
DD
V
2.0V
≤
V
DD
≤
5.5V
D032
MCLR, OSC1 (RC mode)
(1)
V
SS
—
0.2 V
DD
V
D033
OSC1 (XT and LP modes)
V
SS
—
0.3
V
D033A
OSC1 (HS mode)
V
SS
—
0.3 V
DD
V
V
IH
Input High Voltage
I/O ports:
—
D040
with TTL buffer
2.0
—
V
DD
V
4.5V
≤
V
DD
≤
5.5V
D040A
0.25 V
DD
+ 0.8
—
V
DD
V
2.0V
≤
V
DD
≤
4.5V
D041
with Schmitt Trigger buffer
0.8 V
DD
—
V
DD
V
2.0V
≤
V
DD
≤
5.5V
D042
MCLR
0.8 V
DD
—
V
DD
V
D043
OSC1 (XT and LP modes)
1.6
—
V
DD
V
D043A
OSC1 (HS mode)
0.7 V
DD
—
V
DD
V
D043B
OSC1 (RC mode)
0.9 V
DD
—
V
DD
V
(Note 1)
I
IL
Input Leakage Current
(2)
D060
I/O ports
—
±
0.1
±
1
μ
A
V
SS
≤
V
PIN
≤
V
DD
,
Pin at high-impedance
D061
MCLR
(3)
—
±
0.1
±
5
μ
A
V
SS
≤
V
PIN
≤
V
DD
D063
OSC1
—
±
0.1
±
5
μ
A
V
SS
≤
V
PIN
≤
V
DD
, XT, HS and
LP oscillator configuration
D070*
I
PUR
GPIO Weak Pull-up Current
50
250
400
μ
A
V
DD
= 5.0V, V
PIN
= V
SS
V
OL
Output Low Voltage
(5)
D080
I/O ports
—
—
0.6
V
I
OL
= 8.5 mA, V
DD
= 4.5V (Ind.)
V
OH
Output High Voltage
(5)
D090
I/O ports
V
DD
– 0.7
—
—
V
I
OH
= -3.0 mA, V
DD
= 4.5V (Ind.)
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
not tested.
Note
1:
In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
clock in RC mode.
2:
Negative current is defined as current sourced by the pin.
3:
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
normal operating conditions. Higher leakage current may be measured at different input voltages.
4:
See Section 10.4.1 “Using the Data EEPROM” for additional information.
5:
Including OSC2 in CLKOUT mode.