Atmel SAM4S-EK2 Atmel ATSAM4S-EK2 ATSAM4S-EK2 Ficha De Dados
Códigos do produto
ATSAM4S-EK2
Evaluation Kit Hardware
SAM4S-EK2 User Guide
4-4
11176A–ATARM–24-Sep-12
The SAM4SD32 chip internally generates the following clocks:
SLCK, the Slow Clock, which is the only permanent clock of the system
MAINCK, the output of the Main Clock Oscillator selection: either a Crystal Oscillator or a 4/8/12 MHz
Fast RC Oscillator
Fast RC Oscillator
PLLACK, the output of the Divider and 60 to 130 MHz programmable PLL (PLLA)
PLLBCK, the output of the Divider and 60 to 130 MHz programmable PLL (PLLB)
4.3.4
Reset Circuitry
On-board NRST button BP1 provides an external reset control of the SAM4SD32.
The NRST pin is bidirectional. It is handled by the on-chip reset controller. It can be driven low to provide
a reset signal out to the external components. Conversely, it can be asserted low from the outside to
reset the microcontroller Core and the peripherals. The NRST pin integrates a permanent pull-up resistor
of 100 kOhm to VDDIO.
a reset signal out to the external components. Conversely, it can be asserted low from the outside to
reset the microcontroller Core and the peripherals. The NRST pin integrates a permanent pull-up resistor
of 100 kOhm to VDDIO.
On the SAM4S-EK2 board, the NRST signal is connected to the LCD module and JTAG port.
Note:
At power-on, the NRST signal is asserted with a default duration of 2 clock cycles. That duration may not be
sufficient to correctly reset any other system or board devices connected to that signal. First, in your custom
application, you need to check for these device’s datasheets about reset duration requirements. Then, you
need to set an appropriate configuration in the NRST Manager. This is done through the ERSTL field in the
RSTC_MR register. The NRST duration is thereby configurable between 60 µs and 2 s, whether it is subse-
quently activated by a software reset or a user reset. Refer to the SAM4SD32 datasheet for in-depth
information.
sufficient to correctly reset any other system or board devices connected to that signal. First, in your custom
application, you need to check for these device’s datasheets about reset duration requirements. Then, you
need to set an appropriate configuration in the NRST Manager. This is done through the ERSTL field in the
RSTC_MR register. The NRST duration is thereby configurable between 60 µs and 2 s, whether it is subse-
quently activated by a software reset or a user reset. Refer to the SAM4SD32 datasheet for in-depth
information.
4.3.5
Power Supply and Management
The SAM4S-EK2 board is supplied with an external 5V DC block through input J9. It is protected by a
PolyZen diode (MN9) and an LC combinatory filter (MN10). The PolyZen is used in the event of an incor-
rect power supply connection.
PolyZen diode (MN9) and an LC combinatory filter (MN10). The PolyZen is used in the event of an incor-
rect power supply connection.
The adjustable LDO regulator MN12 is used for the 3.3V rail main supply. It powers all the 3.3V compo-
nents on the board.
nents on the board.
Figure 4-4.
Power Block
The SAM4SD32 product has different types of power supply pins:
VDDIN pin:
Power for the internal voltage regulator, ADC, DAC, and analog comparator power supplies.
The voltage ranges from 1.8V to 3.6V.
DGND
+5V
DGND
+5V
+3V3
C75
100uF
100uF
+
C75
100uF
100uF
C65
22uF
22uF
+
C65
22uF
22uF
C64
100nF
100nF
C64
100nF
100nF
MN10
BNX002-01
BNX002-01
MN10
BNX002-01
BNX002-01
SV
1
SG
2
CV
3
CG1
4
CG2
5
CG3
6
C76
100nF
100nF
C76
100nF
100nF
C66
22uF
22uF
+
C66
22uF
22uF
MN9
ZEN056V130A24LS
ZEN056V130A24LS
MN9
ZEN056V130A24LS
ZEN056V130A24LS
1
2
3
R92
102K 1%
102K 1%
R92
102K 1%
102K 1%
MN12
MIC29152W U
MIC29152W U
Micrel's 1.5A LDO, TO263-5
MN12
MIC29152W U
MIC29152W U
Micrel's 1.5A LDO, TO263-5
VIN
2
VOUT
4
SD
1
GND1
3
ADJ
5
GND2
6
R89
169K 1%
169K 1%
R89
169K 1%
169K 1%
J9
MP179P 2.1mm
J9
MP179P 2.1mm
1
2
2
3