Atmel ATmega328P Xplained Mini MEGA328P-XMINI MEGA328P-XMINI Ficha De Dados
Códigos do produto
MEGA328P-XMINI
214
ATmega48A/PA/88A/PA/168A/PA/328/P [DATASHEET]
Atmel-8271H-AVR- ATmega-Datasheet_08/2014
times higher than the SCL frequency. Note that slaves may prolong the SCL low period, thereby reducing the
average TWI bus clock period. The SCL frequency is generated according to the following equation:
average TWI bus clock period. The SCL frequency is generated according to the following equation:
TWBR = Value of the TWI Bit Rate Register.
PrescalerValue
= Value of the prescaler, see
Note:
Pull-up resistor values should be selected according to the SCL frequency and the capacitive bus line load. See
22.5.3 Bus Interface Unit
This unit contains the Data and Address Shift Register (TWDR), a START/STOP Controller and Arbitration
detection hardware. The TWDR contains the address or data bytes to be transmitted, or the address or data
bytes received. In addition to the 8-bit TWDR, the Bus Interface Unit also contains a register containing the
(N)ACK bit to be transmitted or received. This (N)ACK Register is not directly accessible by the application
software. However, when receiving, it can be set or cleared by manipulating the TWI Control Register (TWCR).
When in Transmitter mode, the value of the received (N)ACK bit can be determined by the value in the TWSR.
detection hardware. The TWDR contains the address or data bytes to be transmitted, or the address or data
bytes received. In addition to the 8-bit TWDR, the Bus Interface Unit also contains a register containing the
(N)ACK bit to be transmitted or received. This (N)ACK Register is not directly accessible by the application
software. However, when receiving, it can be set or cleared by manipulating the TWI Control Register (TWCR).
When in Transmitter mode, the value of the received (N)ACK bit can be determined by the value in the TWSR.
The START/STOP Controller is responsible for generation and detection of START, REPEATED START, and
STOP conditions. The START/STOP controller is able to detect START and STOP conditions even when the
AVR MCU is in one of the sleep modes, enabling the MCU to wake up if addressed by a Master.
STOP conditions. The START/STOP controller is able to detect START and STOP conditions even when the
AVR MCU is in one of the sleep modes, enabling the MCU to wake up if addressed by a Master.
If the TWI has initiated a transmission as Master, the Arbitration Detection hardware continuously monitors the
transmission trying to determine if arbitration is in process. If the TWI has lost an arbitration, the Control Unit is
informed. Correct action can then be taken and appropriate status codes generated.
transmission trying to determine if arbitration is in process. If the TWI has lost an arbitration, the Control Unit is
informed. Correct action can then be taken and appropriate status codes generated.
22.5.4 Address Match Unit
The Address Match unit checks if received address bytes match the seven-bit address in the TWI Address
Register (TWAR). If the TWI General Call Recognition Enable (TWGCE) bit in the TWAR is written to one, all
incoming address bits will also be compared against the General Call address. Upon an address match, the
Control Unit is informed, allowing correct action to be taken. The TWI may or may not acknowledge its address,
depending on settings in the TWCR. The Address Match unit is able to compare addresses even when the AVR
MCU is in sleep mode, enabling the MCU to wake up if addressed by a Master.
Register (TWAR). If the TWI General Call Recognition Enable (TWGCE) bit in the TWAR is written to one, all
incoming address bits will also be compared against the General Call address. Upon an address match, the
Control Unit is informed, allowing correct action to be taken. The TWI may or may not acknowledge its address,
depending on settings in the TWCR. The Address Match unit is able to compare addresses even when the AVR
MCU is in sleep mode, enabling the MCU to wake up if addressed by a Master.
22.5.5 Control Unit
The Control unit monitors the TWI bus and generates responses corresponding to settings in the TWI Control
Register (TWCR). When an event requiring the attention of the application occurs on the TWI bus, the TWI
Interrupt Flag (TWINT) is asserted. In the next clock cycle, the TWI Status Register (TWSR) is updated with a
status code identifying the event. The TWSR only contains relevant status information when the TWI Interrupt
Flag is asserted. At all other times, the TWSR contains a special status code indicating that no relevant status
information is available. As long as the TWINT Flag is set, the SCL line is held low. This allows the application
software to complete its tasks before allowing the TWI transmission to continue.
Register (TWCR). When an event requiring the attention of the application occurs on the TWI bus, the TWI
Interrupt Flag (TWINT) is asserted. In the next clock cycle, the TWI Status Register (TWSR) is updated with a
status code identifying the event. The TWSR only contains relevant status information when the TWI Interrupt
Flag is asserted. At all other times, the TWSR contains a special status code indicating that no relevant status
information is available. As long as the TWINT Flag is set, the SCL line is held low. This allows the application
software to complete its tasks before allowing the TWI transmission to continue.
The TWINT Flag is set in the following situations:
After the TWI has transmitted a START/REPEATED START condition.
After the TWI has transmitted SLA+R/W.
After the TWI has transmitted an address byte.
After the TWI has lost arbitration.
After the TWI has been addressed by own slave address or general call.
After the TWI has received a data byte.
SCL frequency
CPU Clock frequency
16 2(TWBR)
PrescalerValue
+
-----------------------------------------------------------------------------------------
=