HK Audio HK LUCAS NANO ADD ON PACKAGE TWO 1007249 Ficha De Dados
Códigos do produto
1007249
Add-On Package Two is an accessory kit for HK Audio’s Lucas Nano. It contains two
adjustable Easy-Click mounts with a connecting cord (2 m), as well as an Allen wrench
(4 mm). Designed to hold one Lucas Nano mid/high unit each, the mounts swivel and tilt
to align speakers.
Replacing the cord
The 2 m double-stranded cord with the 6.3 mm plug may be replaced with
installed speaker wire for wall mounting.
installed speaker wire for wall mounting.
1. Remove the four fl at-head screws
(1)
on the upper side of the Easy-
Click connector
(2)
and fl ip it back.
2. Remove the screw below
(3)
holding the center plate
(6)
in place.
3. Remove the washer
(4)
and spring
(5)
.
4. Carefully lift the center plate
(6)
and tip it back.
5. Remove the retaining cleat
(7)
by unscrewing the two Phillips head
screws
(8)
.
6. Unscrew the two Phillips head screws
(9)
and remove the cord
(10)
from
the connecting terminal.
7. Insert the installed speaker cord through the rear opening and attach it
to the terminal by tightening the Phillips head screws
(9)
.
HEADS UP: Please make sure the polarity is correct. The “+” terminal is on the left
and is labeled accordingly.
8. Proceed in the reverse order to reassemble the mount.
Applications
The Add-On Package Two mounts may be used on a fl at surface such as
a table and on any wall that is able to handle the load.
a table and on any wall that is able to handle the load.
For use as table mounts
1. Remove the contents of Add-On Package Two from the box.
2. Set the Lucas Nano mid/high units on the Easy-Click connectors and
2. Set the Lucas Nano mid/high units on the Easy-Click connectors and
push them forward toward the front of the mounts until you hear a
clearly audible ‘click.’
clearly audible ‘click.’
3. Connect the speaker cords to the Lucas Nano’s Speaker Out ports.
4. Place the mid/high units on the table, tilting and aligning the speakers
4. Place the mid/high units on the table, tilting and aligning the speakers
as you see fi t.
For use as wall mounts
1. Remove the contents of Add-On Package Two from the box.
2. Remove the socket head bolt from the hinge using the included Allen
2. Remove the socket head bolt from the hinge using the included Allen
wrench
(1)
.
3. Remove the retainer plate
(2)
and rotate it 180°.
4. Put the retainer plate back in place and fasten it using the socket head
bolt.
5. Place the mount on the wall where you want the speakers to be. Attach
it to the wall using 1 to 3 screws up to 5 mm in diameter, threading
them through the holes
them through the holes
(3)
in the retainer plate.
6. Set the Lucas Nano mid/high units on the Easy-Click connectors and
push them forward toward the front of the mounts until you hear a
clearly audible ‘click.’
clearly audible ‘click.’
7. Connect the speaker cords to the Lucas Nano’s Speaker Out ports.
8. Now you can adjust the vertical tilt angle as you see fi t. You can also
8. Now you can adjust the vertical tilt angle as you see fi t. You can also
turn the speaker 30° to the left or right.
Tip:
If the cord is not long enough, an extension cord with a ¼" (6.3 mm) jack and plug may
be used to extend its length. Such cables are available in well-stocked music stores.
It may also be replaced with a longer cord that is suitable and laid out properly for the
location at which it is to be used.
English
Mounting instructions 1.1
1
2
3
1
2
3
4
5
6
7
8
9
10
–
+
HK Audio® • Postfach 1509 • 66595 St. Wendel • Germany • info@hkaudio.com • www.hkaudio.com • International Inquiries: fax +49-68 51-905 215 • international@hkaudio.com