HP 932 Black Original Ink Cartridge CN057AE#GBX Ficha De Dados
Códigos do produto
CN057AE#GBX
Environmental hazards
Not classified as an environmental hazard.
Components
CAS #
Percent
EC-No.
Classification
3. COMPOSITION/INFORMATION ON INGREDIENTS
616-45-5
10 - 15
2-pyrrolidone
Xi;R36/38
210-483-1
Proprietary
7.5 - 10
Co-Solvent
Proprietary
1333-86-4
2.5 - 5
Carbon black
215-609-9
7732-18-5
> 70
Water
231-791-2
Composition comments
This ink supply contains an aqueous ink formulation.
This product has been evaluated using criteria specified in the EU Directives 67/548/EEC and
1999/45/EC, as amended.
For the full text of the R phrases mentioned in this Section, see Section 16.
This product has been evaluated using criteria specified in the EU Directives 67/548/EEC and
1999/45/EC, as amended.
For the full text of the R phrases mentioned in this Section, see Section 16.
Carbon black is present only in a bound form in this preparation.
4. FIRST AID MEASURES
Inhalation
Remove to fresh air. If symptoms persist, get medical attention.
Skin contact
Wash affected areas thoroughly with mild soap and water. Get medical attention if irritation
develops or persists.
develops or persists.
Eye contact
Do not rub eyes. Immediately flush with large amounts of clean, warm water (low pressure) for at
least 15 minutes or until particles are removed. If irritation persists get medical attention.
least 15 minutes or until particles are removed. If irritation persists get medical attention.
Ingestion
If ingestion of a large amount does occur, seek medical attention.
5. FIRE-FIGHTING MEASURES
Flash point
> 110 °C (> 230 °F) Pensky-Martens Closed Cup
Suitable extinguishing media
For small (incipient) fires, use media such as foam, sand, dry chemical, or carbon dioxide.
For large fires use very large (flooding) quantities of water and/or foam, applied as a mist or spray.
For large fires use very large (flooding) quantities of water and/or foam, applied as a mist or spray.
Extinguishing media which
must not be used for safety
reasons
must not be used for safety
reasons
None known.
Unusual fire & explosion
hazards
hazards
None known.
Specific methods
None established.
Hazardous combustion
products
products
Refer to section 10.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions
Wear appropriate personal protective equipment.
Environmental precautions
Do not let product enter drains. Do not flush into surface water or sanitary sewer system.
Containment procedures
Dike the spilled material, where this is possible. Absorb with inert absorbent such as dry clay, sand
or diatomaceous earth, commercial sorbents, or recover using pumps.
or diatomaceous earth, commercial sorbents, or recover using pumps.
Methods for cleaning up
Soak up with inert absorbent material.
Other information
Soak up with inert absorbent material. Slowly vacuum or sweep the material into a bag or other
sealed container. Dispose of in compliance with federal, state, and local regulations. See also
section 13 Disposal considerations.
sealed container. Dispose of in compliance with federal, state, and local regulations. See also
section 13 Disposal considerations.
7. HANDLING AND STORAGE
Handling
Avoid contact with skin, eyes and clothing.
Storage
Keep out of the reach of children. Keep away from excessive heat or cold.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Additional exposure data
Exposure limits have not been established for this product.
Exposure controls
Use in a well ventilated area.
Occupational exposure controls
General
Use personal protective equipment to minimize exposure to skin and eye.
Hygiene measures
Handle in accordance with good industrial hygiene and safety practice.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Not available.
Physical state
Liquid
Material name: CN057Series
11120 Version #: 01 Revision date: 06-Dec-2011 Print Date: 04-Jan-2012
SDS GERMANY
2 / 4