Graupner Hendheld RC 2.4 GHz No. of channels: 5 33110 Manual Do Utilizador
Códigos do produto
33110
108 Program description: base settings - helicopter
Base settings
Basic model-specifi c settings for model helicopters
Before you start programming specifi c parameters,
some basic settings must be entered which apply only to
the currently active model memory.
some basic settings must be entered which apply only to
the currently active model memory.
Stick mode
Basically there are four possible ways of arranging the
principal control functions of a model helicopter on
the two dual-axis sticks: the primary functions are roll,
pitch-axis, tail rotor and throttle / collective pitch. Which
of these options you select depends on your individual
preferences and fl ying style:
principal control functions of a model helicopter on
the two dual-axis sticks: the primary functions are roll,
pitch-axis, tail rotor and throttle / collective pitch. Which
of these options you select depends on your individual
preferences and fl ying style:
To select the stick mode, fi rst select the transmitter
mode „ normal“ with the mode switch. Turn the transmit-
ter OFF and insert the supplied programming plug into
the DATA socket on the back of the transmitter. Turn ON
the transmitter: you can now call up the desired stick
mode by cycling through the modes with a brief press of
the BIND-button:
mode „ normal“ with the mode switch. Turn the transmit-
ter OFF and insert the supplied programming plug into
the DATA socket on the back of the transmitter. Turn ON
the transmitter: you can now call up the desired stick
mode by cycling through the modes with a brief press of
the BIND-button:
Buzzer
LED Description
transmitter
buzzers 1x
buzzers 1x
orange LED on Country setting
Universal/Europe
transmitter buz-
zers 2 times
zers 2 times
orange LED
fl ashes
fl ashes
County setting
France
France
The country setting is described in detail below.
transmitter buz-
zers 3 times
zers 3 times
orange LED on »MODE 1«
transmitter buz-
zers 4 times
zers 4 times
orange LED on »MODE 2«
transmitter buz-
zers 5 times
zers 5 times
orange LED on »MODE 3«
transmitter buz-
zers 6 times
zers 6 times
orange LED on »MODE 4«
To choose a mode, hold the BIND-button pressed for
approx. three seconds. When you release the button, the
transmitter should emit an audible signal and the buzzer
sound stops. Switch OFF the transmitter and remove
the programming plug.
Never use the remote control with programming
connector plugged in!
Later, to check the stick mode which is programmed,
watch out for the Status-LED on the transmitter.
approx. three seconds. When you release the button, the
transmitter should emit an audible signal and the buzzer
sound stops. Switch OFF the transmitter and remove
the programming plug.
Never use the remote control with programming
connector plugged in!
Later, to check the stick mode which is programmed,
watch out for the Status-LED on the transmitter.
Country setting
After you have set the stick mode, the country setting
must be done in a second step.
The Country setting is present in order to cater for vari-
ous directives (FCC, ETSI, IC etc.). The HoTT 2.4 radio
system features a restricted frequency band for France.
must be done in a second step.
The Country setting is present in order to cater for vari-
ous directives (FCC, ETSI, IC etc.). The HoTT 2.4 radio
system features a restricted frequency band for France.
If you wish to use the RC system in France, the country
setting on the transmitter must be set to “France” mode,
as described. It is essential not to use the Universal/
EUROPE mode.
To select a Country setting, you must fi rst switch the
transmitter off, then insert the supplied programming
plug in the DATA socket on the back and the Jumper
in the position „NO MIX“ on the front of the transmitter.
Switch the transmitter on: you can now toggle between
the “GENERAL” and “France” settings by briefl y pressing
the BIND-button:
setting on the transmitter must be set to “France” mode,
as described. It is essential not to use the Universal/
EUROPE mode.
To select a Country setting, you must fi rst switch the
transmitter off, then insert the supplied programming
plug in the DATA socket on the back and the Jumper
in the position „NO MIX“ on the front of the transmitter.
Switch the transmitter on: you can now toggle between
the “GENERAL” and “France” settings by briefl y pressing
the BIND-button:
Buzzer
LED Description
transmitter
buzzers 1x
buzzers 1x
orange LED on Country setting
Universal/Europe
transmitter buz-
zers 2 times
zers 2 times
orange LED
fl ashes
fl ashes
County setting
France
France
To choose a country, hold the BIND-button pressed for
approx. three seconds. When you release the button, the
transmitter should emit an audible signal and the buzzer
sound stops. Switch OFF the transmitter and remove
the programming plug.
Never use the remote control with programming
connector plugged in!
Later, to check the country setting which is programmed,
watch out for the Status-LED on the transmitter.
approx. three seconds. When you release the button, the
transmitter should emit an audible signal and the buzzer
sound stops. Switch OFF the transmitter and remove
the programming plug.
Never use the remote control with programming
connector plugged in!
Later, to check the country setting which is programmed,
watch out for the Status-LED on the transmitter.
“MODE 2” (Throttle at left stick)
“MODE 3” (Throttle at right
stick)
“MODE 4” (Throttle at left stick)
“MODE 1” (Throttle at right stick)
pitch axis
tail rotor
pitch axis
tail rotor
throttle
roll
roll
throttle
tail rotor
tail rotor
throttle
throttle
pitch axis
pitch axis
roll
roll
pitch axis
pitch axis
roll
roll
Motor/Pitch
throttle
tail rotor
tail rotor
throttle
throttle
roll
roll
pitch axis
pitch axis
tail rotor
tail rotor