Graupner Hendheld RC 2.4 GHz No. of channels: 5 33110 Manual Do Utilizador
Códigos do produto
33110
128 Program description: Trainer system
menu: no transmitter controls have been released to the
Pupil ( ), and no switches have been assigned (SW: ---
bottom right and -S on left of illustration).
Pupil ( ), and no switches have been assigned (SW: ---
bottom right and -S on left of illustration).
–P
T
2 3 4 5 6
BIND: N/A
SW: –––
1
TRAINER/Pupil
Start the “BINDING” process fi rst at the Pupil transmitter
by pressing the central
by pressing the central
SET
button of the right-hand
four-way button, the display
n/v
changes to the message
BINDING
:
Binding the Pupil transmitter to the Teacher trans-
mitter
mitter
Note:
During the binding procedure the distance between the
two transmitters should not be too great. You may need
to change the relative position of the two transmitters
and initiate the binding process a second time.
During the binding procedure the distance between the
two transmitters should not be too great. You may need
to change the relative position of the two transmitters
and initiate the binding process a second time.
The teachers
mx-10 transmitter HoTT must be bound
conclusively to the pupils transmitter. To do this press
the BIND button on the front. After a few seconds a suc-
cessful binding operation is confi rmed by a short beep,
the trainer model can be controlled with the teacher
transmitter.
When using a
the BIND button on the front. After a few seconds a suc-
cessful binding operation is confi rmed by a short beep,
the trainer model can be controlled with the teacher
transmitter.
When using a
mx-12/16/20 HoTT pupil transmitter,
BINDING
changes to
ON
:
To perform the transfer, move the mode switch of the
mx-10 HoTT in forward direction- in the mode „pupil“.
As long as this switch is pressed, the pupil has control
over the trainer model. Release the key to give the
control back to the teacher transmitter.
Note: even if the transmitter is turned off temporarily, the
teacher mode remains active when turned on again.
mx-10 HoTT in forward direction- in the mode „pupil“.
As long as this switch is pressed, the pupil has control
over the trainer model. Release the key to give the
control back to the teacher transmitter.
Note: even if the transmitter is turned off temporarily, the
teacher mode remains active when turned on again.
Pupil transmitter settings
mx-10 HoTT
The trainer model must be programmed completely,
i. e. with all its functions including trims and any mixer
functions in the
i. e. with all its functions including trims and any mixer
functions in the
mx-10 HoTT Teacher transmitter. This
means that it must be possible to control the trai-
ner model fully, without restriction, by the Teacher
transmitter. But, at the conclusion of these prepara-
tions, the trainer model must be bound to the Pupil
transmitter.
When assigning the control functions the usual conven-
tions should be observed:
ner model fully, without restriction, by the Teacher
transmitter. But, at the conclusion of these prepara-
tions, the trainer model must be bound to the Pupil
transmitter.
When assigning the control functions the usual conven-
tions should be observed:
Channel
Function
1
Throttle / Collective pitch
2
Aileron / Roll
3
Elevator / Pitch-axis
4
Rudder / Tail rotor
–P
T
2 3 4 5 6
BIND:
ON
SW: –––
1
TRAINER/Pupil
The HoTT receiver of the trainer model must be „bound“
to the pupils transmitter. A detailed description of the
binding process can be found on page 106 and 109.
Note: the
to the pupils transmitter. A detailed description of the
binding process can be found on page 106 and 109.
Note: the
mx-10 HoTT binding procedure can only be
done in „normal“ mode. Before using the transmitter in
Pupil mode, bind the receiver in mode „normal“, then
switch to the mode „pupil“. In addition, no mixer may be
activated, move the jumper in the middle position „NO
MIX“, see also page 105.
After the pupils transmitter is bound to the trainer model,
set the
Pupil mode, bind the receiver in mode „normal“, then
switch to the mode „pupil“. In addition, no mixer may be
activated, move the jumper in the middle position „NO
MIX“, see also page 105.
After the pupils transmitter is bound to the trainer model,
set the
mx-10 HoTT in the pupils mode. To change
the mode, move the mode switch on the transmitter in
the „pupil“ position, press and hold the BIND-button and
then switch on the transmitter.
the „pupil“ position, press and hold the BIND-button and
then switch on the transmitter.
Binding the Pupil transmitter to the Teacher trans-
mitter
mitter
Note:
During the binding procedure the distance between the
two transmitters should not be too great. You may need
to change the relative position of the two transmitters
and initiate the binding process a second time.
During the binding procedure the distance between the
two transmitters should not be too great. You may need
to change the relative position of the two transmitters
and initiate the binding process a second time.
Press and hold the BIND-button of the pupils transmitter
mx-10 HoTT.
mx-10 HoTT.
Teacher transmitter:
mx-10 HoTT: press and hold the BIND-button
After a few seconds the successful binding is confi rmed
by a short beep, the trainer model can be controlled with
the teacher transmitter.
mx-12/16/20 HoTT: Switch on the transmitter, and
use the arrow buttons of the left or right-hand four-way
button to leaf through on both transmitters to the “Trai-
mx-10 HoTT: press and hold the BIND-button
After a few seconds the successful binding is confi rmed
by a short beep, the trainer model can be controlled with
the teacher transmitter.
mx-12/16/20 HoTT: Switch on the transmitter, and
use the arrow buttons of the left or right-hand four-way
button to leaf through on both transmitters to the “Trai-