Avers Stratus 21 MW Matt White W-E-ST-02121-MW Manual Do Utilizador
Códigos do produto
W-E-ST-02121-MW
3.6. Stratus/Akustratus s
.
creen programming.
Programing the length of the rolled out screen (screen bottom bar position).
- Roll up the screen until it will stop automatically in the upper position.
- Insert regulation wrench included in the screen set into the regulation slot (see picture. 6) located in the left bottom
part of the screen .
Regulation knob “2” (back) enables setting of the lower extreme position of the screen bottom bar:
„+” - means increasing the lenght of the fabrics is rolled down when the screen is rolled out,
„–” - means decreasing the length of the fabrics is rolled down when the screen is rolled out.
- Insert regulation wrench included in the screen set into the regulation slot (see picture. 6) located in the left bottom
part of the screen .
Regulation knob “2” (back) enables setting of the lower extreme position of the screen bottom bar:
„+” - means increasing the lenght of the fabrics is rolled down when the screen is rolled out,
„–” - means decreasing the length of the fabrics is rolled down when the screen is rolled out.
!!! NOTICE !!! The screen was programmed properly at the factory and there is no need to reprogram it without any
important reason. Setting of screen extreme positions was made by manufacturer.
important reason. Setting of screen extreme positions was made by manufacturer.
If you need to change the screen extreme position follow the instructions described below.
3.7.
The Stratus screens with built-in +RC control system was programmed at the factory. Screen programming can be
performed with the remote control transmitter based on the programming procedure. Detailed programming procedure is
described in the separate programming manual supplied with the screen.
described in the separate programming manual supplied with the screen.
For safety reasons the screen can be operated manually in case of the remote transmitter or remote transmitter battery
failure. To do so the electric switch must be applied to the screen control cables (see picture 10). Press the switch button,
the screen engine will start operation and will continue as long as the switch button is pressed (screen will roll down). The
next time the switch button will be pressed the screen engine will start operation again, the screen rotation direction will be
changed (screen will roll up). The engine will stop operation automatically as soon as the programmed screen bottom bar
end position will be reached.
the screen engine will start operation and will continue as long as the switch button is pressed (screen will roll down). The
next time the switch button will be pressed the screen engine will start operation again, the screen rotation direction will be
changed (screen will roll up). The engine will stop operation automatically as soon as the programmed screen bottom bar
end position will be reached.
3.8.
+RC remote control system programming
Akustratus remote control system programming
In order to use more than one Akustratus screen at the same location requires the screen control system will be
programmed different control codes. In order to control single screen with multiple remote transmitters requires all
transmitters to be coded with the same control code. Screen controller and remote transmitters control codes can be
programmed with programming jumpers located at the screen controller board and the remote transmitter main board with
the following way:
transmitters to be coded with the same control code. Screen controller and remote transmitters control codes can be
programmed with programming jumpers located at the screen controller board and the remote transmitter main board with
the following way:
- De-install screen from the wall/ceiling installation brackets and place at the flat surface (i.e. table, etc.). The screen
should be placed with the screen closing flap facing up,
- De-install left plastic side cover to access the screen controller board,
- Open the transmitter bottom cover unwrap the mounting screw,
- You can change the screen controller and transmitter control codes by changing location of the programming jumpers.
- The transmitter will operate with the screen in case the picture created with the programming jumpers at the
- Open the transmitter bottom cover unwrap the mounting screw,
- You can change the screen controller and transmitter control codes by changing location of the programming jumpers.
- The transmitter will operate with the screen in case the picture created with the programming jumpers at the
transmitter will be the mirror picture of the programming jumpers at the screen controller board (see picture 12).
!!! IMPORTANT !!!
Do not decrease (tuning knob 1+) the range of the rolled down surface. It can damage the screen.
Do not increase (regulation 2+) the range of the surface which was rolled down behind the STOP mark, placed in
the upper right corner of the screen. Rolling down the screen behind the mark can damage the screen.
Do not decrease (tuning knob 1+) the range of the rolled down surface. It can damage the screen.
Do not increase (regulation 2+) the range of the surface which was rolled down behind the STOP mark, placed in
the upper right corner of the screen. Rolling down the screen behind the mark can damage the screen.
9
23A 12V
Remote
transmitter
transmitter
Screen
controller board
Programing jumpers mirror pictures
Picture 12 Akustratus remote control system programing
Transmitter
jumper area
jumper area
Controller
jumper area