Hitachi hard disk 0J11285 500 GB 2.5 " 8 MB 0J11285 Ficha De Dados
Códigos do produto
0J11285
Z5K500 OEM Specifications
130
14.33 Security Unlock (F2h)
Command Block Output Registers
Command Block Input Registers
Register
7 6 5 4 3 2 1 0 Register
7 6 5 4 3 2 1 0
Data
- - - - -
-
-
- Data
- - - - - -
-
-
Feature
- - - - -
-
-
- Error
...See
Below...
Sector
Count
- - - - -
-
-
- Sector
Count
- - - - - -
-
-
LBA
Low
- - - - -
-
-
- LBA
Low
- - - - - -
-
-
LBA
Mid
- - - - -
-
-
- LBA
Mid
- - - - - -
-
-
LBA
High
- - - - -
-
-
- LBA
High
- - - - - -
-
-
Device
- - - - -
-
-
- Device
- - - - - -
-
-
Command
1 1 1 1 0 0 1 0 Status
...See
Below...
Error Register
Status Register
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
CRC UNC 0
IDN
0
ABT T0N AMN BSY RDY
DF
DSC DRQ COR IDX ERR
0 V 0 0 0 V 0 0
0 V 0 - - 0 0 V
Table 102 Security Unlock Command (F2h)
This command unlocks the password and causes the device to enter device unlock mode. If COMRESET
with Software Setting Preservation disable or power on reset is done without executing the Security
Disable Password command after this command is completed, the device will be in device lock mode.
The password has not been changed yet.
with Software Setting Preservation disable or power on reset is done without executing the Security
Disable Password command after this command is completed, the device will be in device lock mode.
The password has not been changed yet.
The Security Unlock command requests to transfer a single sector of data from the host including
information specified in the following table.
information specified in the following table.
If the Identifier bit is set to master and the file is in high security mode then the password supplied will be
compared with the stored master password. If the file is in maximum security mode then the security
unlock will be rejected.
compared with the stored master password. If the file is in maximum security mode then the security
unlock will be rejected.
If the Identifier bit is set to user, then the file compares the supplied password with the stored user
password.
password.
If the password compare fails then the device returns an abort error to the host and decrements the
unlock attempt counter. This counter is initially set to 5 and is decremented for each password mismatch.
When this counter reaches zero then all password protected commands are rejected until a power off.
unlock attempt counter. This counter is initially set to 5 and is decremented for each password mismatch.
When this counter reaches zero then all password protected commands are rejected until a power off.
Word Description
00 Control
word
bit 0
: Identifier (1-Master, 0-User)
bit 1-15
: Reserved
01-16 Password
(32
bytes)
17-255 Reserved
Table 103 Security Unlock Information
Identifier
Zero indicates that device regards Password as User Password. One indicates that
device regards Password as Master Password.
device regards Password as Master Password.
The user can detect if the attempt to unlock the device has failed due to a mismatched password as this
is the only reason that an abort error will be returned by the file AFTER the password information has
been sent to the device. If an abort error is returned by the device BEFORE the password data has been
sent to the file then another problem exists.