In-Tech electronic BT65N Folheto

Note:

MATERIAL:

SIZE:

OTHER:

2006/03/07

Lucy

8042

MCB-8042010-0A

#8042 USER MANUAL

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.

These limits are

designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure
compliance requirements, please avoid direct contact to the transmitting
antenna during transmitting.

Federal Communication Commission

Interference Statement

c. While listening to music (for example, song 2), press the Speaker's

FORWARD >> button (Fig.2) will skip to next song (for example, song 3);
press the BACKWARD << button (Fig.2) will replay the current song (for
example, song 2). The fast forward & backward are also supported by
holding the FORWARD >> or BACKWARD << function keys. This remote
control function is supported only by the AVRCP profile in your
enabled devices.

d. Turn the Speaker off after use.

Remark: Details operation of music playing through

A2DP profile

varies from different Mobile Phones / PDAs.

Bluetooth

II. Traveller Speaker paired with Stereo Audio Adaptor

Guide

BT 65N

When you purchase a Combo pack with BT90S Traveller Speaker and BT 65N
Stereo Audio Adaptor, please follow this Guide.

Bluetooth Audio Adaptor

Bluetooth

Traveller Speaker

1. Pairing

a. While the Speaker is powered off

switch the power ON/OFF switch (Key

2) to the “I” position to turn it on (Fig.1).

The Power LED (Fig.3) will

become blue. Press and hold

ON/OFF/Pairing/Pause switch

(Fig.2) for 4 seconds, the

LED will flash red and green

alternatively, which indicates the Speaker in Pairing Mode. The Pairing
Mode will last for one minute.

b. While the BT 65N Stereo Audio Adaptor is powered off, press and hold

PLAY and STOP buttons simultaneously.

The LED will flash red and

green alternatively, which indicates the Audio Adaptor is in Pairing Mode.
The Paring Mode will last for one minute.

Put the Speaker and the Audio Adaptor close to each other, 0.5 to 3

meters. After a few seconds, their LED's on two devices will turn into
flashing green, which indicates successful pairing.

Both units are in

Standby Mode and ready to transmit audio signal, or music from the audio
source (Fig.5).

，

Bluetooth

2. Listening to music

a. After successful pairing, plug the jack of the Audio Adaptor to the 3.5 mm

socket of any audio source such as iPod, MP3, CD player, Notebook PC,
or other audio devices with audio jack.

b. Play the music on the audio source as normal; you will listen to the stereo

music from the speaker.

c. The Music volume can only be adjusted by pressing and releasing the

VOL+ / VOL - buttons of audio source.

d. Turn the Speaker off after use and the Audio Adaptor will be turned off

automatically. Next time, you don't need to pair them again. Turn them
on, and then they will be paired automatically and ready to transmit music
from the audio source.

III. Traveller Speaker connected directly with Audio Device Guide

1. Listening to music

a. While the Speaker is powered off, switch the power ON/OFF switch (Key 2)

to the “I” position to turn it on (Fig.1). The Power LED (Fig.3) will become
blue.

b. Plug one end of the audio cable to the “Audio input socket” (socket 4,

Fig.1) of the Traveller Speaker and the other end to the 3.5 mm socket of
any audio source such as iPod, MP3, CD player, Notebook PC or other
audio devices.

c. Play the music on the audio source as normal; you will listen to the stereo

music from the speaker.

d. The Music volume can only be adjusted by pressing and releasing the VOL

+ / VOL- buttons of audio source.

e. Turn the Speaker off after use.

Accessories Table

Standalone pack

(BT90S)

Combo pack

(BT90S+BT65N)

Included

Audio cable

BT 65N Audio Adaptor

Not Included

Included

(Fig.5)

Included

3XAAA batteries

Not Included

USB Power cable

for BT65N

Remarks: Specification of A/C power adaptor for BT90S
DC Voltage input: 5V, 500mA
DC plug:

(1.35 X 3.5 X 11) mm

210.00 mm

297.00