Behringer Eurolight LC2412 Manual Do Utilizador

EUROLIGHT LC2412 User Manual

(62)

(63)

Fig. 2.11: Serial number and mains connector

(62) 

SERIAL NUMBER. Please take a few minutes and send to us a completely 

filled out warranty card within 14 days of the original date of purchase. 

Otherwise, warranty claims may be rendered invalid. Or will out the 

warranty information online at behringer.com.

(63) 

FUSE COMPARTMENT / VOLTAGE SELECTION. Before connecting the unit 

to a power outlet, please make sure that the selected voltage matches your 

local voltage. When replacing fuses, please make sure that you always use 

fuses of the same type. Some units allow for switching between 230 V 

und 120 V. Please note: when connecting a unit intended for the European 

market to a 120 V power outlet, you must also replace the factory fuse with a 

higher-value fuse.
Power is supplied via an IEC connector. The matching cable is provided with 

the unit.

This chapter describes individual steps used to set up, recall and fade in/out 

presets (pre-determined lighting situations). Even though your LC2412 can 

execute complex functions, its controls are easy to master, provided you invest 

some time to familiarize yourself with the way they work. To familiarize you with 

the control elements and their functions step by step, let us begin with setting up 

presets (preset = the total collection of all fader positions of the A PRESET section 

at one particular time). Let’s start with 12 channels first.
All statements referring to channels 1 - 12 apply also to channels 13 - 24 

(upper mode).

A Preset section

Chase memory

Level steps

Memory steps

B Memory section

Fig. 3.1: Using presets and memories

Pull all the faders all the way down to the zero mark. This way, you assure that 

you start your exploration of the possibilities of the LC2412 from a neutral 

setting, and can observe the results of the changes you implement directly. 

Use the POWER switch to power up your BEHRINGER EUROLIGHT LC2412. 

The LC2412 displays now the setup that was most recently used, just prior to 

being powered down last time.
If you want to start completely from the beginning, you can use a key 

combination to erase all programmed configurations. More on this subject 

in chapter 7.8.

3.1.1  Preset mode
To work exclusively with presets, you have to first switch into preset mode. 

Select “P” in the bank display accordingly.
1.  Press the UP or DOWN keys repeatedly until “P” is shown in the display. 

The display flashes for roughly 3 seconds.

2.  Once the flashing stops, your LC2412 is in preset mode. The CHANNEL FLASH 

function is now automatically activated, which is also shown by the lit 

control LED (CH FLASH  

(32)

).

3.  Raise the MAIN fader  

(43)

  as well as Fader A  

(41)

.

4.  You can now use faders 1 - 12 of the A PRESET section to create a stage 

design. The illumination level of individual lighting elements can be read out 

on the control LEDs, aligned next to the FLASH keys.

All operations applicable to channels 1-12 can be executed on channels 13 - 24, 

once you switch into upper mode.
1.  Press the UPPER switch  

(33)

.

The control LED indicates that the LC2412 is now in upper mode, that 

is, that the faders of the A PRESET section now control channels 13 - 24. 

The faders from the B MEMORY section affect channels 13 - 24 while in 

preset mode.

2.  Set up your preset by moving the faders of the A PRESET section into the 

desired position.
In case you had already executed setups to channels 13 - 24, you have to 

first put the faders into the previously selected position before being able to 

again align these channels. 

3.  To quit upper mode, simply press the  switch.

Additional features:
While in upper mode, the flash keys fade in the channels 13 - 24.