Whirlpool Drop-In Ceramic Electric Range Manual Do Utilizador
2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Parts needed
■
A UL listed or CSA approved conduit connector
■
UL listed wire connectors
Parts supplied
■
2 - #8-14 x 1" screws
Check local codes. Check existing electrical supply. See
“Electrical Requirements.”
“Electrical Requirements.”
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
licensed, qualified electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■
It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the right-hand side
oven door trim.
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the right-hand side
oven door trim.
■
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
Given dimensions are minimum clearances.
■
Recessed installation area must provide complete enclosure
around the recessed portion of the range.
around the recessed portion of the range.
■
Grounded electrical supply is required. See “Electrical
Requirements” section.
Requirements” section.
■
Electrical supply junction box should be located on rear wall.
Bottom of junction box should be 30¾" (78.1 cm) max. from
top of countertop.
Bottom of junction box should be 30¾" (78.1 cm) max. from
top of countertop.
■
The anti-tip mounting screws must be installed. See “Install
Range” section.
Range” section.
■
The range should be located for convenient use in the
kitchen.
kitchen.
■
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
or microwave range hood combination that projects
horizontally a minimum of 5" (12.7 cm) beyond the bottom of
the cabinets.
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
or microwave range hood combination that projects
horizontally a minimum of 5" (12.7 cm) beyond the bottom of
the cabinets.
■
Range support slats must be solid, level and flush with
bottom of cabinet cutout. Floor must be able to support a
weight of 225 lbs (102.0 kg).
bottom of cabinet cutout. Floor must be able to support a
weight of 225 lbs (102.0 kg).
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or follow local codes.
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or follow local codes.
Mobile home installations require:
■
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
■
Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See “Electrical Connection” section.
mobile home installation. The appliance wiring will need to be
revised. See “Electrical Connection” section.
Mounting
screw
screw
Tip Over Hazard
A child or adult can tip the range and be killed.
Securely attach mounting screws to cabinet.
Reattach mounting screws if the range is moved.
See installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children and adults.
Making sure the mounting screws are installed:
•
Remove side trim from both sides of the range.
•
Look for screws securely attached to cabinet.
•
Replace side trim.
WARNING
■
Phillips screwdriver
■
Router
■
¹⁄₂" router bit
■
Measuring tape
■
Level